Direct Healthcare Services Dyna-Form Mercury Advance Руководство по эксплуатации - Страница 5
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Внутренняя отделка Direct Healthcare Services Dyna-Form Mercury Advance. Direct Healthcare Services Dyna-Form Mercury Advance 13 страниц.
Печатать страницуD Y N A - F O R M M E R C U R Y A D V A N C E
6.1 Low / High Settings
The Dyna-Form Mercury Advance Mattress, in Alternating Mode, has two pressure settings. The
initial setting that the control unit will revert to upon set up is "Low". The "Low" comfort setting
is ideal for the lighter patient or those who feel discomfort when on a normal alternating air type
mattresses system. However, for patients with existing pressure damage or those at Very High
Risk, it is recommended that dependant on the clinical judgement of the clinician,
the "High" setting is activated by pressing the +/- button once, which is located on top of the
Control Unit.
In "High" Mode the Control Unit attains more of the characteristics of an alternating air mattress
system whilst still utilising the advantages of the static foam inserts. Repeatedly pressing the
'mode' button enables the Low & High modes to be selected in turn.
6.2 CPR Deflation
The CPR system consists of a manually operated button located on the Air Inlet connector
attached to the Control Unit. By pressing the Red Button, which will release the connector locking
system, the user can remove the connector unit which will deflate the mattress air system back to
that of a static foam mattress.
Note: After a short period as the Mattress deflates the 'Low Pressure' Audible Warning is
activated and can be cancelled by switching the Control Unit off.
6.3 Troubleshooting
For assistance (if needed) in setting up, using or maintaining the Mercury Advance System, or to
report unexpected operation or events, please contact Direct Healthcare Group on the contact
details on the reverse of this manual.
7. Audible/Visual Indicators
Warning conditions are indicated by a flashing red display accompanied by an Audible Warning.
In each case the user should respond by turning the Control Unit's switch off and investigating the cause.
7.1 High Pressure Warning
This condition could be caused, for example by a kinked Umbilical Hose or visitors,
and others, sitting suddenly on the Mattress.
7.2 Low Pressure Warning
This condition could be caused, for example, by incorrect fitting of the air inlet connector,
opening of the CPR Valve or a leak in the Mattress due to a cut or puncture.
7.3 Mains Failure Warning
This condition may be caused, for example if Mains power is lost.
7.4 Alternating Mode Failure (no alternation)
This will be indicated by a warning LED on A and B and an Audible Warning.
1. Reset the warning – turn off Power and press the Audible Warning mute button.
2. Disconnect the air hoses to reduce pressure – reconnect when pressure has decreased.
7.5 Initialising Failure
This will be indicated by a warning LED on A, B and C and an Audible Warning.
1. Press the Audible Warning mute button to silence the Audible Warning.
2. Check the power cable is firmly plugged into the mains outlet and the Control Unit;
and check the mains power is switched on.
3. Check the Control Unit fuse (1 AMP) – fuses can be released using a screwdriver
to push and turn.
8
D I R E C T H E A L T H C A R E G R O U P . C O M
S E R V I C E M A N U A L
8. Transportation
To change the location of the mattress, remove the Umbilical Cord and allow the mattress to return to its Static Mattress form.
Switch off the Control Unit using the on/off switch and disconnect the electrical supply cable from the mains socket. The mattress
can now be moved to a new location where it must immediately be reconnected to the mains electrical supply and the Control Unit
switched back on. Once the Mattress has been refilled, the 'Alternating' mode will automatically revert back to the Low setting and
should be reselected to High should this be desired by the clinician.
Warning: The Mattress will not ' a lternate' when disconnected from Control Unit and /or the mains electrical. Also, refer to environmental
conditions section at rear of this manual.
9. Cleaning & Maintenance Procedures
9.1 Cleaning Procedures
Warning: Before cleaning the System make sure that the Control Unit is disconnected from the mains electricity supply.
Do not immerse the Control Unit in water or other fluids.
Do not autoclave, nor use phenol for cleaning.
Do wash hands before commencing the cleaning process.
Wear appropriate protective clothing such as gloves, apron
and a mask.
Ensure all work surfaces are cleaned before and after contact with the Mattress.
9.1.1 Cleaning the Mattress
1. Cleaning should take place before and after use, and between patients.
2. With cover left on the Mattress disconnect the Mattress from the Control Unit.
3. Clean the surface of the wash down table with Hypochlorite solution or equivalent disinfectant.
4. Wash Mattress top using hot water (60 degrees C) containing detergent – dry with a paper towel.
5. Use a Hypochlorite solution 1,000 parts per million available chlorine. For heavy contamination use a Hypochlorite solutions 10,000
parts per million available chlorine. Please ensure thorough rinsing after cleaning.
6. Using suitable brush, hot water, detergent or Hypochlorite solution, clean Umbilical Hose and CPR Valve. Dry with
paper towel.
7. If required, the Mattress Cover may be removed and machine-washed at a temperature of 80 degrees C, for not less than 10
minutes. The individual Air Cells can be wiped down with established disinfectants.
8. To avoid shrinkage of the coverline dry in an indoor clean environment or tumble dry on a low heat setting not exceeding 40
degrees C and not for longer than 10 minutes. Covers must be thoroughly dried before re-fitting to the mattress.
9.1.2 Cleaning the Control Unit
The Control Unit can be cleaned by wiping with a cloth dampened with a detergent solution with the above recommended DiffX
dissolved within a spray bottle filled with 500ml of warm water. Also, refer to symbol chart.
9.2 Identification of the Control Unit (Serial Number)
The Control Unit is identified by serial number and GS1 compliant barcoding using
both 128 and 2D bar code identifiers.
Both product code and manufacture date are shown on the identification label.
The above Control Unit serial number is MA15090002 and manufacture date is 02
day of 09 month of year 2015.
D I R E C T H E A L T H C A R E G R O U P . C O M
9