Xerox WORKCENTRE 7120 Справочное руководство - Страница 19

Просмотреть онлайн или скачать pdf Справочное руководство для Принтер Xerox WORKCENTRE 7120. Xerox WORKCENTRE 7120 29 страниц. Color networking mfp a3
Также для Xerox WORKCENTRE 7120: Руководство для оценщиков (25 страниц), Руководство для оценщиков (24 страниц), Справочное руководство (30 страниц), Технические характеристики (14 страниц), Технические характеристики (14 страниц), Сравнение конкурентов (11 страниц), Сравнение конкурентов (11 страниц), Брошюра и технические характеристики (4 страниц), Руководство по быстрому использованию (20 страниц), Руководство по быстрому использованию (20 страниц), Руководство по быстрому использованию (20 страниц), Руководство по быстрому использованию (20 страниц), Руководство по установке (2 страниц), Руководство по установке (2 страниц), Руководство по быстрому использованию (20 страниц), Справочное руководство (32 страниц), Руководство системного администратора (20 страниц)

Печатать страницу
Xerox WORKCENTRE 7120 Справочное руководство
Time (in mi Iliseconds)
Event
Card reader receives val id read order and reader is in II busy automatic ll state. light check occurs
0 - , - - , - - - - - - - at this time. If light check fails, the read indicator will light, the reader will switch to IInot op-
60
70
80
90
100
110
erational ll and an lIunusual end ll will be signaled to the controlling system.
---t-----i-------
Column 1 arrives at read station. Mode change (EBCDIC to binary) will occur at this time if rows
1 and 2 are punched.
210 -01-....J....------Column 80 arrives at read station.
220
230
240
End of card is detected; card reader signals IIchannel end ll to controlling system. Card reader
returns to II ready II condition (a new SIO can be accepted if no interrupt is pending) unless the con-
troll ing system specifies command chaining, in which case the reader requests a new read order.
250
--®-Newfeedcycle enabledatthistimeifnewvalidorder present and readerstill inllautomatic ll mode.
Notes:
®
Feed cycle is usually approximately 47 ms but can be as long as 200 ms (in case of slippage or slight jam).
If a card has not been fed after 200 msec, the transport motor wi II hal t, the reader wi II switch to IInot op-
erational
ll
,
the FEED indicator will light, and an lIunusual end
ll
will be signaled to the controlling system.
®
The data bytes are transmitted, with respect to the column read time (approximatel y 2.05 ms), as shown
below.
1--2.05ms---r-160ms--l
Data available to controlling system
Col. 1
~
t
t
EBCDIC mode:
Transmit one byte
n
n
n
for each column
~ , ' - - - - - - -..... ' - - - - - - - - ' ' - - - - -
~
f1Jl
nn_
Binary mode:
Transmit rows 12-5
~
Store rows 6-9
1
Lr
ransmit rows
2-9
Transmit rows 12-1 plus
rows 6-9 of previous column
t
indicates data overrun will occur at this time if data is not accepted by controlling system.
©
Throat jam detection occurs 215 ms later if card jams in throat area, causing transport motor to halt, FEED
indicator to light, reader to switch to "not operational ", and an lIunusual end" to be signaled to controf-
@
J
i ng system.
Read and timing jam detection occurs 225 ms later if card jams in read and timing area.
Results in same
action as
©
above.
®
Dark check occurs at this time. If dark check fails, the READ indicator will light, the reader will switch to
IInot operational ", and an lIunusual end
II
will be signaled to the controlli ng system.
®
Stacker jam detection occurs 215 ms later if card jams in stacker area. Results in same action as
©
above.
Figure 5. Card Reader Event Times (Model 7121)
Programming Considerations
13