Direct Supply Panacea Руководство пользователя - Страница 2

Печатать страницу

Introduction

Thank you for purchasing this Panacea Reclining Wheelchair. In this owner's

manual, you'll find important information that you should read before

assembling and using this device. If at any time you do not understand

how to use this product, or you suspect it may be damaged, DO NOT USE

and immediately contact the distributor that sold this product to you. This

owner's manual is compiled from the latest specifications and product

information available at the time of publication. Changes may be made to

this manual at any time. Contact your distributor for a current copy of this

owner's manual.

Definitions and Symbols

NOTE: Indicates a tip.

• CAUTION: Means correct operating or maintenance procedures must

be followed in order to prevent damage to or destruction of the product or

other property.

• WARNING: Calls attention to a potential danger that requires correct

procedures or practices in order to prevent personal injury.

PRODUCT or DEVICE: Your Panacea Reclining Wheelchair, distributed by

Direct Supply Manufacturing, Inc.

Warnings and Cautions

Read carefully all directions and warnings before using this device. Do not

operate this device without first reading and understanding the contents of

this manual. Death or injury may result from the improper use of this device or

failure to follow all directions and warnings. This device is intended for use by

or under the supervision of trained and licensed healthcare providers in normal,

indoor conditions.

• WARNING: This wheelchair has not been approved as a seat that can

be used within vehicles of any kind. Always transfer wheelchair user to a

vehicle manufacturers-approved seat and use safety restraints available.

• WARNING: Do not operate this wheelchair on roadways, streets or any

surfaces with vehicular traffic.

• WARNING: Do not attempt to operate on inclines 10° or greater without

proper assistance.

• WARNING: Be sure to completely engage wheel locks when getting in

and out of wheelchair or when in elevator or wheelchair lift.

• WARNING: Wheelchair locks should be used only when the wheelchair

is at a complete stop. The locks are not intended to be used when the

wheelchair is moving. Do not use locks as brakes to slow down.

• WARNING: Wheelchair should be on a smooth, stable and level area

with wheel locks engaged before transferring user in or out of wheelchair.

• WARNING: Do not adjust footrests any lower than 2

• WARNING: When getting in or out of wheelchair, do not stand on or

apply weight to footrests.

• WARNING: Before reaching or leaning forward, rotate casters to front

of the wheelchair and engage wheel locks to help prevent wheelchair

from tipping over.

• WARNING: Do not lean out of the chair or apply weight to the

top of wheelchair back. This can cause wheelchair to tip over. When

trying to extend arms over back, only allow residents to reach as far as

their arm can extend without having to alter their seating position.

• WARNING: DO NOT stand on wheelchair.

• WARNING: Abruptly stopping or changing directions while going up or

down an incline could cause instability or possible tipping over.

• WARNING: A skilled caregiver should assess the appropriateness of

removing footrests or legrests on a case-by-case basis.

• WARNING: Always provide assistance to residents transferring into

and out of this device.

• WARNING: Do not make any modifications to this device or use

non-Panacea parts. Doing so may void the warranty and pose a risk to

the resident.

• CAUTION: State and local codes and regulations may prohibit

the removal of footrests. Check with your local authorities to ensure

compliance with all applicable regulations.

• WARNING: This device may not be suitable for all individuals. A skilled

caregiver should always assess the appropriateness of this device for a

resident on a case by case basis.

Directions for Use

Wheel locks: Engage both wheel locks before getting in or out of chair,

leaning forward in chair, or while in an elevator or wheelchair lift. Proper

adjustment of wheel lock is at least

⁄

" when locked. Locks are engaged

by pushing handle completely forward. Adjustments to locks are made

by loosening or tightening nut on the carriage bolt. Embed lock to show

at least

⁄

" by sliding clamp toward rear wheel while handle is in locked

position. Test for correct locking action and the resident's ability to engage

wheel locks before each use.

Tires: The solid rubber tires on your Direct Supply Panacea Wheelchair

need minimal maintenance, but should be cleaned occasionally with a

damp cloth. Replace if tires become severely worn or if cracking appears.

1-800-634-7328 DirectSupply.com

Front casters: Caster should be checked periodically and lubricated

occasionally. Lubricate by removing fork and greasing caster stem

bearings. Lubricate wheel bearings by removing wheel from fork.

⁄

" from floor.

Reassemble fork and wheel by tightening nuts until no play remains,

but wheels roll freely. If nut is too loose, caster will shimmy. If nut is

too tight, the chair will be difficult to steer.

Removal of swingaway footrests/legrests: Release lock by

pushing on the front rigging lever. Swing footrest/legrest out and

sideways. Lift to remove.

Adjusting length of footrest/legrest: When adjusting length

of footrests or legrests, user should be sitting in wheelchair with

feet on the footplates. Loosen bolt on the clamp around support

assembly. Raise or lower footplate to desired position, taking into

account the support of thighs. Front rigging should not be so low

that it causes uncomfortable pressure to thighs at front of seat

upholstery. Footrest should not be lower than 2

to ensure clearance.

Adjusting/elevating legrest: Lift footplate on legrest assembly to

desired position. Release legrest assembly and it will automatically

lock into place. To lower, push out on legrest lever and lower

footplate to desired position.

Wheels: Large rear wheels should be inspected at least once

a month to ensure proper tightness. If wheel wobbles or is loose,

release lock nut and tighten axle bolt slightly. Test for proper

tightness by leaning chair to one side and spinning adjusted wheel.

General care: Wipe chrome parts with a clean, soft cloth at least

once a week. All metal parts can be cleaned with auto wax or similar

devices. If exposed to moisture, dry immediately. Do not use an

abrasive cleanser that will scratch the finish.

To open chair: Open wheelchair by tilting to one side and pushing

down on seat rail until fully opened.

To close/fold chair: First fold footplates to vertical position. Grab

seat with both hands at front and back edge and lift. Or, tilt chair to

one side and lift up on seat rail.

To remove arms: Remove arms by depressing spring button and

lifting arms out of front and rear sockets.

To recline the chair: Increase or decrease the angle of the back of

the chair by pulling the levers located under the hand grips on the

back of the chair. Do not abruptly change chair back angle. Always

recline the chair in a smooth manner.

⁄

" from the ground