Yamaha DTX522K Руководство по сборке - Страница 2

Просмотреть онлайн или скачать pdf Руководство по сборке для Музыкальный инструмент Yamaha DTX522K. Yamaha DTX522K 2 страницы. Dtx drums series

Печатать страницу

Assembling the snare and tom pads

Push the snare pad onto the rack's snare holder.

Tom pads

Ensure that the snare holder's rod is fully inserted

DTX522K: TP70

into the snare pad's mounting hole, and then tighten

DTX542K: XP70

the clamp bolt to secure the pad in place.

Snare holder

Loosen bolts A to D as shown below to adjust the

XP80 Snare Pad

height and angle of the snare pad's playing surface.

When correctly positioned, be sure to securely re-

 Snare pad

tighten the bolts before proceeding to the next step.

Attach a clamp bolt to the snare pad and provision-

ally tighten (by five or six turns).

Clamp bolt (tighten in the

direction of the arrow)

Underside of snare pad

Assembling the drum module, cymbal pads, and hi-hat pad

 Each cymbal and hi-hat pad

PCY100 Cymbal Pad

PCY135 Cymbal Pad

Using the tuning key, loosen the stopper's key bolt.

PCY100

Hi-hat Pad

Drum module

Remove the wing nut, the two felt pads, and the bolt

cover from the cymbal holder.

A cymbal pad's built-in sensor is located close to the

Yamaha logo found on the top surface. In order to

achieve the best performance from your pad, position

it such that the area around the logo can be easily

struck. (See the figure above.)

 Drum module

Secure the module holder to the bottom of the drum

module using the module holder screws.

Place the stopper on the cymbal holder.

Module holder

* If the key bolt was not sufficiently loosened in

Module holder

Step 1 above, it may not be possible to pass the

Bottom of drum

screws

stopper over the cymbal holder's shaft. In such a

module

case, loosen the key bolt as much as possible

without removing it.

Replace the bolt cover.

Front side

* Turn the bolt cover to tighten it onto the threaded

section and firmly secure it in place.

Push the module holder into the holder clamp and

tighten the clamp bolt to secure it in place.

Drum module

module holder

Push in

Clamp bolt

Holder clamp

 Tom pads

As with the snare pad, attach a wing bolt (DTX522K)

or clamp bolt (DTX542K) to each of the three tom

pads and provisionally tighten (by five or six turns).

Snare pad

Push each of the tom pads onto one of the rack's

Rod

tom holders. Each time, ensure that the tom holder's

rod is fully inserted into the tom pad's mounting

hole, and then tighten the bolt to secure the pad in

place.

Push

DTX522K

Clamp bolt

Tom pad: TP70

Rod

Push

Wing bolt

Tom holder

Loosen bolts A to C as shown below to adjust the

Bolt B

height and angle of each tom pad's playing surface.

When correctly positioned, be sure to securely re-

tighten the bolts before proceeding to the next step.

Bolt D

Bolt C

Bolt A

Bolt C

With the stopper making full contact with the bottom

surface of the bolt cover as shown below, tighten the

stopper's key bolt using the tuning key.

Cymbal pads

Stopper

Key bolt

Bolt cover

Full contact

Tuning key

Cymbal holder

Wing nut

Place one of the felt pads removed in Step 2 on the

cymbal holder.

Felt pads

Mount the pad on the cymbal stand. Lower the pad

into place with the cymbal holder's shaft passing

Bolt cover

through the central hole. When mounted, the stop-

per's pin should rest inside the pad's smaller hole.

* If you were to play your cymbal or hi-hat pad with-

out the stopper's pin positioned well inside the

Cymbal holder

smaller hole, the pad could rotate, causing the ca-

ble to be pulled out. It is very important, therefore,

to ensure that the stopper is secured as shown in

Step 5 above.

Assemble the felt pad that came with the hi-hat or

cymbal pad.

The second felt pad removed from the cymbal

holder in Step 2 above is not required for assem-

bly.

Tighten the wing nut to secure the pad to the cymbal

holder.

Wing nut

Felt pad that

Bolt cover

came with cym-

bal or hi-hat

Cymbal or

hi-hat pad

Stopper

Threaded section

Cymbal holder

Felt pad

Bolt cover

Assembling the kick pad

If a drum mat (sold separately) is not available, lay a sheet of cardboard on the

floor to prevent it from being scratched.

Remove the four wing bolts, spring washers, and flat washers from the kick pad

frame, and line up each set nearby in the order of removal.

Join the base section to the frame as shown on the right, and then secure it in

place by assembling the wing bolts, spring washers, and flat washers removed in

the previous step from the base side.

DTX542K

Tom pad: XP70

Rod

Push

Arrange the hi-hat controller and the kick pad as shown in Example of standard assembly on the other side of this sheet.

Clamp bolt

Tom holder

Lay a drum mat (sold separately) on the floor underneath the hi-hat controller and the kick pad. Alternatively, you can place

NOTICE

cardboard from the drum kit packaging or the like on the floor to prevent it from being scratched.

Connect the pads to the drum module.

Connect the output of each pad to the corresponding drum-module input.

Bolt B

Plug the straight ends of the nine-channel snake cable into the trigger input

jacks ([qSNARE] to [oHI-HAT] and [HI-HAT CONTROL]) on the back of the

drum module.

* DTX542K shown.

• When using the standard setup, the stickers on each of the snake cable's plugs

will indicate the name of the corresponding pad.

Drum-module rear panel

Hi-hat pad

Stopper

Bolt cover

Full contact

Nine-channel

snake cable

Straight

plugs

L plugs

HH CON HI HAT CRASH

Connect the power adaptor to the drum module.

Ensure that the drum module is turned off, and then plug the power adaptor's DC cord into the

nector. Hook the power adaptor's DC cord around the cord clip to secure it in place.

Drum-module rear panel

Stopper

Cymbal or

Cord clip

hi-hat pad

Smaller hole

Using the cable bands, secure the cables to the kit rack at the positions circled in the figure on the right. (

Plug the adaptor's AC cord into a domestic wall socket.

Stopper

Cymbal holder

Your electronic drum kit is now ready.

Frame

Plug the L-shaped ends of the nine-channel snake cable into the corresponding

pads.

Locations of pad jacks

RIDE

TOM3

Straight plug names

DTX502 jack names

(as shown on stickers)

1: qSNARE

SNARE

2: wTOM1/!0

TOM1

3: eTOM2/!1

TOM2

4: rTOM3/!2

TOM3

5: tRIDE

RIDE

6: yCRASH

CRASH

7: uKICK/i

KICK

8: oHI-HAT

HI HAT

HH CON

9: HI HAT CONTROL

In the case of snare and tom pads, wrap the cables around the cable clips to pre-

vent them from being pulled out.

NOTICE

KICK

SNARE TOM1 TOM2 TOM3 RIDE

connector

* For instructions on turning on the drum module, producing sounds, and other subsequent steps,

Spring washer

Flat washer

Wing bolt

Frame

Base

CRASH

HI HAT

SNARE

TOM2

HH CON

TOM1

KICK

Excessive bending can damage pad cables. Ensure, therefore,

that these cables are not bent at an extreme angle when

wrapped around the clips.

con-

)

please refer to the Owner's Manual that came with the module.