Yamaha ATS-1010 Руководство пользователя - Страница 16
Просмотреть онлайн или скачать pdf Руководство пользователя для Акустическая система Yamaha ATS-1010. Yamaha ATS-1010 19 страниц. Front surround system
Также для Yamaha ATS-1010: Руководство пользователя (20 страниц)
Печатать страницу
Refer to the chart below
should the unit not function
properly.
If' the problem you are experiencing
is not listed below,
or if the instruction
below does not help, set the unit to the standby
mode, disconnect
the AC power supply cable, and
contact
the nearest authorized
Yamaha
dealer or service center. Check the below first.
1 The AC power supply cable of the unit, TV and external
components
(such as BD player) are firmly connected
to
the AC wall outlet.
2 The power supply of' the unit, TV and the external
components
(such as BD player) are turned on.
3 All cables are firmly connected
to their respective
jacks on each component.
Power turns on but
immediately
shuts oft'.
The speakers
make no
sound,
Surround
effect is not
achieved,
No bass / The external
subwoot'er
makes no sound.
The power cable may be connected
improperly.
Make sure the power cable is plugged into the
4
outlet firmly.
The unit may have received a strong electrical
Set the unit to standby mode, and then
shock, such as l_om a lightening
boll or
disconnect
the power cable. Wait lk)l"about 30
excessive static electricity,
seconds, connect the power cable, and then turn
the unil oil again.
The unit has an auto-sleep
lkmclion, which will
lett turned on lk)r 12 hours without any
automatically
set to standby mode if the unit is
operation being pertk)rmed.
Tile volume may be set to minimum.
The mute hmction may be activated.
The
input
source
or input
setting
may
be
incorrect.
A surround
mode
is ]lot selected.
Adjust the volume level.
Press MUTE on the Ivmote control to cancel the
mute hmclion and adjust the volume.
Select tile correct input source or input setting.
Press SURROUND
on the remote control to
play back the source in surround effi:cl.
Adjusl the vohune level of lhe subwool)r.
8
8
7
7
8
8
5
Select collect setting ol subwooti_r.
Connect
the unit and the external subwoofer
by
using a subwooli?r pill cable.
The volume of the subwooler
channel may be
set
to
minimuln
level.
Opposite setting of subwooti:r
is selected.
The source does ilol conlain low frequency
signals.
The cable between the unit and the subwooti:r
not connected
when selecting playback of the
external subwooti2r.
The volume
level decreases
The uili[ controls its volume within a certain
Reset the volume.
8
without
any
operation,
level to prevent the next playback lrom sudden
output at excessive
volume.
This unit does not operate
The unit may ivceive a strong electrical
shock,
Set the unit to standby mode, and theli
properly,
such as from a lightening bolt or excessive
static
disconnect
the power cable. Wait lor about 30
electricity, or drop ill power supply,
seconds, connect the power cable, and then mrn
on the unit again.
A digRal
or high-frequency
The unit may be placed close to digital
Place the unit away from such equipment.
equipment
produces
noises,
eqllipmenl or high-lrequency
equipment.
The remote control does not
The unit may be outside the remote coiItrol
The operation range lor the remote control of
6
operate
the unit.
operation range,
the unit is within 6 m (20 1i).
The remote control sensor of the unit may be
Change the lighting or ivposition the unit.
exposed to direct sunlight or other lighting.
The batteries may be worn out.
Replace tile batteries.
6
The Volume of the unit and "IV
Your TV itself received the signal lrom TV
Set the volume of your TV to minimum,
or set
increases
simultaneously,
remote control, having learned the operation of
the audio output of your TV builtqn speaker to
the unit.
oil.
Adjust the volume by using the remote control
8
of the unit.
12 En