Yamaha DXS12 mkll Руководство пользователя

Просмотреть онлайн или скачать pdf Руководство пользователя для Акустическая система Yamaha DXS12 mkll. Yamaha DXS12 mkll 2 страницы. Dxr and dxs series powered speakers and subwoofers
Также для Yamaha DXS12 mkll: Руководство пользователя (22 страниц), Руководство (12 страниц), Руководство пользователя (2 страниц), Руководство пользователя (22 страниц), Руководство по эксплуатации (на английском языке) (22 страниц), Руководство по эксплуатации (на английском языке) (22 страниц), (Русский) (22 страниц)

Печатать страницу

Yamaha DXS12 mkll Руководство пользователя

POWERED SUBWOOFER

Owner's Manual

DXS18

• The DXS18 is mainly used for the explana-

tions in this manual.

DXS15 mkll

• The illustrations as shown in this manual are

for instructional purposes only.

• The company names and product names used

DXS12 mkll

in this manual are the trademarks or registered

trademarks of their respective companies.

Introduction

Thank you very much for purchasing the DXS Powered Subwoofer. The DXS is a powered subwoofer used

for sound reinforcement and temporary installations. This owner's manual explains how to set up and use

the subwoofer in live venues and temporary PA installations to enhance low-end sound. Be sure to read this

manual before using this subwoofer, in order to make sufficient use of the many functions that this product

offers. Also, be sure to keep this manual after you are finished reading it.

Included accessories

Optional accessories

• AC power cord

• Speaker cover: SPCVR-18S01 (for DXS18), SPCVR-DXS152 (for DXS15mkII), SPCVR-DXS122 (for DXS12mkII)

• Owner's manual (this leaflet)

• Wheels: SPW-1; 4 pieces

• Technical Specifications

q Pole sockets

u INPUT jacks

Adapts to commercially available speaker poles of 35 mm diameter and

These are balanced input XLR jacks (line-level), and this device outputs

M20 screws. For details on installing speaker poles, refer to "Installing

the mixed signals of L and R.

a Speaker Pole."

i OUTPUT jacks

w Feet cups

These are balanced output XLR jacks for connecting full-range speak-

When stacking multiple DXS units, align the rubber feet of the upper

ers or additional DXS units. The output signal can be switched via the

DXS unit to the feet cups of the lower.

THROUGH/HPF POST switch (o).

L/R output from the OUTPUT jacks correspond to L/R input to the

CAUTION

INPUT jacks. The mixed signal of L/R is not output.

Do not stack more than two DXS units.

o THROUGH/HPF POST switch

Switches the signals output from the OUTPUT jacks (i).

e Front LED

Turns on when the power is on. Lights more brightly when the output

limiter is active. Using FRONT LED DISABLE switch (!9 ) allows you

to defeat the front LED altogether.

• THROUGH: Outputs unaffected signals from INPUT jacks (u).

r Wheel mounting holes

Select when using HPF of the connected speaker or connecting addi-

Optional SPW-1 wheels can be installed at these locations. For details

tional DXS units.

on installing the wheels or special precautions you should take, please

• HPF POST: Outputs signal input from INPUT jacks (u) after pass-

refer to the relevant manual for the wheels.

ing through a HPF. The cutoff frequency of the high pass filter is the

t AC IN inlet (V-Lock)

frequency specified with the X-OVER switch (!2 ) . Because the out-

Connect the AC power cord included with the unit. The AC power cord

put level from the OUTPUT jacks is linked to the LEVEL control

includes a locking mechanism with a latch. First connect the DXS to the

(!1 ) , the levels of this unit and the full-range speaker change simulta-

AC power cord, and then connect the power cord to the AC outlet.

neously.

When removing the cord, push the latch while pulling the cord out.

!0 PEAK indicator

CAUTION

Lights red when the input level reaches 3 dB below clipping. If the indi-

cator lights frequently, adjust the volume of the input source or lower

Turn off the power before you connect or discon-

the LEVEL control (!1 ) so that the indicator flashes only briefly at the

nect the power cord.

highest input levels.

y Power switch

!1 LEVEL control

Turns the power to the unit on ( ) or off (

Adjusts the output level.

If you are using multiple units, turn on the power to each unit one by

!2 X-OVER switch

one. If you turn on the power to multiple units simultaneously, a tempo-

Specifies the crossover frequency at 120 Hz, 100 Hz, or 80 Hz. The out-

rary drop in the power voltage may occur, possibly resulting in abnor-

put from the unit is processed through a low pass filter to cut the range

mal operation of the units.

of the selected frequency or higher. When setting THROUGH/HPF

Also, rapidly turning the unit on and off in succession can cause it to

POST switch (o) to [HPF POST], the output signals from the OUT-

malfunction. After turning the unit off, wait for about 5 seconds before

PUT jacks are processed through a high pass filter to cut the range of

turning it on again.

the selected frequency or lower, and the crossover frequency is linked to

CAUTION

that of the connected speaker.

A slight electrical current will flow even when the

power switch is turned off. Make sure to unplug

the power cord from the power outlet when not

using the speaker for an extended period of time.

ZZ20050

Features



High power, high sound pressure, superior low-end playback capabilities

Adopting a bandpass type enclusure for high sound pressure. The DXS features a high-resistance input,

low distortion woofer and a 1,020 W power amplifier to achieve superior low-end playback capability

and high sound pressure.



Flexible features

• D-XSUB: D-XSUB is a DSP technology that gives users additional dynamic control of the frequency

range to meet the demands of a variety of applications or musical styles.

• Selectable X-OVER (80/100/120 Hz): Selecting the cut-off frequency and LPF/HPF settings offers

users more flexibility to adapt to various applications.

• Cardioid mode: The Cardioid mode setting adds additional control of low frequencies for sub-woofer

arrays of two or more DXS speakers, effectively reducing the SPL of bass directed towards the stage

while increasing the bass levels directed towards the audience.



Reliability

A high-performance DSP control protects the speaker and amplifier. The DXS can be used worry-free,

even under harsh operating conditions.



Durability

The DXS's sturdy plywood cabinet is covered with an extremely durable polyurea finish that provides

added protection from outside elements.



Fast and easy setup

M20 and Ø35 mm dual pole sockets allow for more flexible set up, while optional casters are also avail-

able for improved portability.

Controls and functions

t y

!3 D-XSUB switch

Switches the low-range frequency response characteristics.

• NORMAL: A generic setting corresponding to various applications.

• BOOST: Boosts the frequency range enhancing and providing punch

to the sound.

• XTD LF (eXTenDed LF): Extends the bottom of the low frequency

range.

!4 CARDIOID switch

Connection of multiple DXS units enables the use of Cardioid mode.

For details on Cardioid mode and using the switch, refer to "Setup of

Cardioid Mode" on the opposite page.

!5 POLARITY switch

CAUTION

Switches the polarity of the unit, normal or inverted. When the polarity

Make sure to lower the input level when switching.

is inverted, the INVRT indicator lights.

In most cases, this should be set to normal; however, the inverted setting

may improve low-range response, depending on the type and location of

the speaker system. Select a setting that produces the best low-end

sound.

!6 LIMIT indicator

Lights when the output limiter is active. The output limiter operates in

order to protect the speaker and amplifier, attenuating the output signal

to the amplifier. If the indicator lights frequently, adjust the volume of

the input source or lower the LEVEL control (!1 ) so that the indicator

only occasionally lights at the highest input levels.

!7 PROTECTION indicator

Lights when the protection system is active. The protection system

operates and the speaker output is muted in the following situations.

• If amplifier overheating is detected.

• If overcurrent is detected.

• Immediately after turning the power on. (The protection system is

activated to prevent noise and the indicator lights for about two sec-

onds. The indicator turns off when the power supply has started nor-

mally.)

!8 POWER indicator

Lights when the power is on.

!9 FRONT LED DISABLE switch

Turns the FRONT LED at the front of the unit on or off. The LED lights

when this switch is set to off. Turn this switch on to disable the LED.

Input the output signal from a source, such as a mixer, to the INPUT jack of the DXS, and input the output

signal from the OUTPUT jack of the DXS to the input jack of a full-range speaker.

• X-OVER switch (!2 )

It is recommended that you match the crossover frequency (the cutoff frequency of the low pass filter)

of the DXS and the cutoff frequency of the high pass filter of the full-range speaker. The same fre-

quency range output from the DXS and the full-range speaker may cause interference with each other

and degrade the frequency characteristics.

• THROUGH/HPF POST switch (o)

If the full-range speaker is properly equipped with a high pass filter, you should set this to

[THROUGH]. The [THROUGH] setting enables you to control the level independently and minimize

signal delay. If the full-range speaker is not equipped with a high pass filter or the high pass filter in the

full-range speaker cannot be set to the same cutoff frequency as that of the low pass filter of the DXS,

set this to [HPF POST] to use the high pass filter in the DXS.

 Combination and setting examples

Full-range

speaker

Full-range

speaker

From

DXS

mixer

CAUTION

If multiple powered speakers are connected in daisy-chain fashion, turn each device on

in sequence starting from the one nearest to the sound source, and turn them off start-

ing from the one farthest from the sound source.

Combination of monaural DXS and stereo full-range speakers

Full-range speaker

Combination of stereo DXS and stereo full-range speakers

NOTE

The L and R jacks are interchangeable; there is no difference in behavior between them.

Full-range speaker

DXS

Basic Setup

This is a pole socket used to mount a full-range speaker atop the DXS. The pole socket is compatible with

35 mm or M20 speaker poles, available commercially. When using the pole socket, be sure that the follow-

ing conditions are met.

DXS18

DXS15mkII

Using the high pass filter in the

Using the high pass filter in

connected full-range speaker

the DXS

DXS12mkII

Installing optional wheels SPW-1 at the back of the DXS enables you to transport the unit easily. To install

the wheels, use the screws already installed in the DXS unit.

Please do not use the speaker once the screws are removed. This causes air leaks to occur in enclosure,

resulting in undesirable performance.

Full-range speaker

From mixer

DXS

Power does not turn on.

Power suddenly turned

off.

No sound.

To full-range speaker

Sound is interrupted

Mixer

suddenly.

Sound howls (feed-

back).

The sound from each

speaker differs (if multi-

ple speakers are used.)

Sound is distorted.

* If any specific problem should persist, please contact your Yamaha dealer.

From mixer

System Type

Frequency Range (-10 dB)

Measured Maximum SPL (Peak)

Full-range speaker

Pink Noise @1m

Power

Amplifier

Components

Dimensions

To full-range speaker

(W × H × D; including rubber feet)

Weight

Handles

Pole Sockets (top surface)

Connectors

Input Sensitivity (LEVEL: center)

DXS

Maximum Input Level

Mixer

* The contents of this manual apply to the latest specifications as of the publishing date.

To obtain the latest manual, access the Yamaha website then download the manual file.

Installing a Speaker Pole

Ø35

M20 screw

Subwoofer

Top-mounted speaker

Pole length

Weight 28.0 kg or less, height 76 cm or less (DSR115)

120 cm or less

Weight 19.3 kg or less, height 61 cm or less (DXR12)

100 cm or less

Weight 14.6 kg or less, height 51 cm or less (DXR10)

82 cm or less

Weight 13.5 kg or less, height 46 cm or less (DXR8)

90 cm or less

Installing Wheels

CAUTION

• For details on installing the wheels or special precautions you should take, please

refer to the relevant manual for the wheels.

• Do not install wheels other than the SPW-1.

Troubleshooting

Symptom

Possible causes

Possible solution

The power cord is not con-

Connect the power cord properly.

nected properly.

The protection system has

Turn off the power, wait until the amplifier cools down,

been activated, shutting

and then turn on again.

down the power supply.

The cable is not con-

Connect the cable to the INPUT jack properly.

nected properly.

The protection circuit has

Wait until the amplifier cools down. If the unit doesn't

been activated, muting the

automatically reset itself, turn off the power, and then

output.

on again.

A microphone is directed

Keep the speaker away from the area where the

toward the speaker.

microphone picks up the sound.

The settings for each

Set each switch of each speaker to the same posi-

speaker differ.

tion.

Lower the volume of the input device so that the

Input volume is excessive.

PEAK indicator lights only occasionally.

Output volume is exces-

Lower the output level with the LEVEL control so that

sive.

the LIMIT indicator lights only occasionally.

General Specifications

DXS18

DXS15mkII

DXS12mkII

Powered subwoofer, band-pass type

32 Hz–120 Hz

40 Hz–150 Hz

42 Hz–150 Hz

136 dB SPL

135 dB SPL

134 dB SPL

Dynamic

1,020 W

Power

Rating

Continuous

800 W

Power Consumption

100 W

(1/8 output power)

18" cone,

15" cone,

12" cone,

4" voice coil

2.5" voice coil

563 × 683 × 721 mm 480 × 611 × 614 mm 400 × 567 × 570 mm

49.7 kg

36.0 kg

Steel, side × 2

Ø35 mm (depth: 80 mm), M20 (threaded depth: 25 mm)

Input

XLR3-31 × 2

Output

XLR3-32 × 2 (THROUGH or HPF POST)

Power

IEC AC inlet × 1 (V-Lock)

+10 dBu

+24 dBu

30.0 kg