Yamaha YSP-CU4300 Краткое справочное руководство - Страница 2
Просмотреть онлайн или скачать pdf Краткое справочное руководство для Акустическая система Yamaha YSP-CU4300. Yamaha YSP-CU4300 2 страницы. Quick reference guide
Печатать страницу
Installation
Connection
Settings
Playback
Carrying out AUTO SETUP for appropriate surround effects
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud
test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the
AUTO SETUP procedure is in progress.
1.
Place the IntelliBeam microphone at your normal listening position.
Assemble the cardboard microphone stand and place the IntelliBeam microphone on top of it horizontally as shown below.
1
2
3
4
Place horizontally
Fit in
Remove
Fit in
Use the supplied cardboard microphone stand to place the IntelliBeam microphone at the same height as your ears would be when you
are seated.
Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct
the path of sound beams.
IntelliBeam microphone
Upper limit
Center height of
this unit
Within 1 m (3.3 ft)
Within 1 m (3.3 ft)
Center
line
Cardboard
Listening
microphone stand
position
1.8 m (6.0 ft)
Lower limit
or more
Cardboard microphone stand
2.
3.
Press the
key on the remote control.
Turn the TV on and switch the TV's input to
The power of this unit turns on.
display video content from this unit.
When this unit is connected to the HDMI input on the TV (as
shown in "Connecting a TV and a Blu-ray disc player" in this
Quick Reference Guide), switch the TV's input to "HDMI1".
yTip
You can select the language for the menu display.
Press and hold the SETUP key until the "OSD LANGUAGE"
menu appears. Press the
/
key to select the desired
language. Press the SETUP key again to exit the setup menu.
4.
Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack on the rear of the unit.
AUTO SETUP
(PREPARATION & CHECK)
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from Sound Pro-
jector. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
IntelliBeam microphone (supplied)
Cardboard microphone stand (supplied)
5.
Make sure that your listening room is as quiet as possible.
For accurate measurement, turn off air conditioner or other devices that make noises.
Note
Follow the instructions below and then leave the room. If you remain in the room, you may obstruct the beam, or the microphone may
pick up any sounds you make, possibly resulting in improper configuration of settings.
When leaving the room, bring this Quick Reference Guide with you. The AUTO SETUP procedure takes about 3 minutes. Wait outside
the room during the AUTO SETUP procedure.
To cancel the AUTO SETUP procedure after it is started, press the RETURN key on the remote control.
5
6.
Press the ENTER key to start the AUTO
Run
SETUP procedure and then leave the room
through
within 10 seconds.
The screen automatically changes during the AUTO
SETUP procedure.
If the AUTO SETUP procedure is complete, this unit rings
the chimes and the results will be displayed on the TV.
If "ENVIRONMENT CHECK:Failure" is displayed, see
page 27 of the Owner's Manual and run the measurement
process again.
yTips
• The results displayed depend on the position of the
unit.
• If you hear a buzzer sound and an error message
appears on the TV, look for a solution in "If an error
message is displayed" on page 27 of the Owner's
Manual. Then press the RETURN key to run the
measurement process again.
IntelliBeam
microphone
7.
Press the ENTER key.
Measurement results are applied to this unit.
• You can save the several measurement results
pressing the SYSTEM MEMORY key (see page 28 of
the Owner's Manual).
8.
Remove the IntelliBeam microphone.
Keep the IntelliBeam microphone in a safe place.
The settings are automatically saved in the system
memory.
Installation
Connection
Playing back
Confirm that this unit and other audio/video devices are properly connected by playing a DVD or BD on the Blu-ray disc player. The following
explains the playback procedure when this unit, TV, and Blu-ray disc player are connected as shown in "Connecting a TV and a Blu-ray disc
player" in this Quick Reference Guide.
1.
Press the
2.
Turn on your TV and Blu-ray disc player connected to this
1
unit.
AUTO SETUP START
3
Will begin in 10 sec.
3.
Press the HDMI1 key to select the Blu-ray disc player as the
Please leave the room
input source.
7
----------
[RETURN]:Cancel
HDMI1
(After 3 min.)
4.
Switch the TV's input to HDMI 1.
SHOW RESULT
5.
Play back a DVD or BD on the Blu-ray disc player.
MESUREMENT COMPLETE.
6
ENVIRONMENT CHECK: Success
BEAM MODE: 5Beam/Plus2
6.
Press the VOLUME (+/-) key to adjust the volume.
yTip
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
Use TV remote control to mute the sound from TV.
7.
Press the SURROUND key and then the CINEMA DSP keys
to set your sound preferences.
yTips
AUTO SETUP COMPLETE
When this unit does not play back, check the following
• The connection between this unit and Blu-ray disc player.
Please remove the MIC
• The audio output settings of Blu-ray disc player is set to digital sound output.
from Sound Projector
and the listening position.
• The TV's input is switched to this unit.
Press [SYSTEM MEMORY] key
to save set-up in the memory.
■
Enjoying TV in surround sound
1.
Select the desired TV channel.
2.
Press the TV key.
■
FM tuning (YSP-4300 only)
Settings
Playback
1.
Press the FM key.
key to turn on this unit.
■
Playing music stored on an iPod via YIT-W12TX
1.
Connect YIT-W12TX to the iPod.
Input source name
■
Playing music stored on a computer via YIT-W12TX
1.
Connect YIT-W12TX to the computer via the
USB cable for YIT-W12TX.
USB
■
Playing music stored on an iPod or USB device over a USB connection (YSP-4300 only)
Connect the iPod to the USB jack on the front
of this unit using the USB cable supplied with
the iPod.
yTip
HDMI control function
You can use the TV remote control to operate this unit if your
TV supports the HDMI control function. See page 31 of the
Owner's Manual.
For more information on playing music stored on the iPod,
refer to "Playing music stored on an iPod or USB device over
a USB connection" in the Owner's manual.
For detailed operation, refer to the Owner's Manual on the supplied CD-ROM.
2.
Press the TUNING
/
key to specify the
frequency.
For details of YIT-W12TX, refer to "Safety and
Accessory Information" (separate booklet).
2.
Start playback of music stored on the iPod.
For details of YIT-W12TX, refer to "Safety and
Accessory Information" (separate booklet).
2.
Play music stored on the computer.
Connect a USB device to the USB jack on the
front of this unit.
For more information on playing music stored on USB device,
refer to "Playing music stored on an iPod or USB device over
a USB connection" in the Owner's manual.