Clarke CAT91 Руководство по эксплуатации и техническому обслуживанию - Страница 5
Просмотреть онлайн или скачать pdf Руководство по эксплуатации и техническому обслуживанию для Электроинструмент Clarke CAT91. Clarke CAT91 8 страниц. Air ratchet wrench
Также для Clarke CAT91: Инструкции по эксплуатации и техническому обслуживанию (17 страниц)
Печатать страницу
OPERATING INSTRUCTIONS
Before starting work drain any water from the
air tank and blow condensation from the air
line. Drain compressor more frequently in hot
humid weather.
The speed ratchet was designed, and is
ideally suited for quick removal and
installation of nuts, bolts, spark plugs and other
fasteners where space is limited.
For removal , set direction of rotation, forward
or reverse, choose correct socket etc to fit
fastener, place Speed Ratchet on fastener
and break loose by hand. Depress throttle
lever, the air power tool will complete the job.
Use penetrating oil for rusted fasteners if
necessary.
When assembling,start fasteners by hand,
again set rotation forward or reverse, apply
Speed Ratchet gently depress throttle lever,
and run down with power.
Since torque is deliberately limited, it is virtually
impossible to overtighten or damage smaller
threads. Final tightening is completed by
hand.
The Speed ratchet is rated at 1/2" bolt size.
Avoid possible internal damage by using tool
only in the normal range of hand ratchet
wrenches of similar drive size.
MAINTENANCE
Daily before use.
1.
Drain water from air tank, air line and
compressor.
2.
Check and clean, if necessary, the air
inlet gauze filter .
3.
Pour a few drops of CLARKE Air Line Oil
(approx 3cc), into the air inlet. This should
be carried out regardless of whether or
not an air line lubricator is used.
If an Air line lubricator is NOT used, this
procedure should be repeated after
every two to three hours of use.
If the Ratchet is to be stored, or is idle for
longer than 24 hours, run a few drops of
Clarke Air Line Oil into the air inlet, and run
the tool for 5 seconds in order to lubricate
the internal parts.
For lubricating the air motor when in
operation, an air line lubricator should be
used, with Clarke Air Line Oil, adjusted to 2
drops per minute.
Clarke Air Line Oil is available from your
CLARKE dealer, part no. 3050825.
Be aware that factors other than the tool may
effect its operation and efficiency, such as
reduced compressor output, excessive drain
on the airline, moisture or restrictions in the
line, or the use of connectors of improper size
or poor condition which will reduce air supply.
Grit or gum deposits in the tool may also
reduce efficiency. This condition can be
corrected by cleaning the air strainer and
flushing out the tool with gum solvent oil,or
failing this, the tool should be dis-assembled,
thoroughly cleaned, dried and re-assembled.
If the tool runs erratically or becomes
inefficient, and the air supply is sound,
dismantle the air motor and replace worn or
damaged parts, or take the tool to your
CLARKE dealer.
IMPORTANT:
The use of parts other than CLARKE
replacement parts may result in safety
hazards, decreased tool performance
and may invalidate your warranty.
SPECIFICATIONS
Model:
Part No:
Square drive
Bolt Capacity
Maximum Torque
Air Pressure
Air Consumption
Max Speed
Air Inlet
Min Hose Size
Length
Weight
- 4 -
CAT 22b
3110411
1/2"
1/2" (13)mm
60 lb/ft
90 PSI (6.2bar)
4 CFM
160 RPM
1/4" BSP
1/4" (6mm) ID
10" (254mm)
1.0 kg