Zanussi ZGG96624 Руководство пользователя - Страница 10
Просмотреть онлайн или скачать pdf Руководство пользователя для Варочная панель Zanussi ZGG96624. Zanussi ZGG96624 16 страниц. Hob
Также для Zanussi ZGG96624: Руководство пользователя (16 страниц), Руководство пользователя (16 страниц), Руководство пользователя (48 страниц), Руководство пользователя (44 страниц)
Печатать страницу
Model .......................................
PNC .........................................
Serial number ...........................
Important safety requirements
This hob must be installed in accordance with
the Gas Safety (Installation and Use)
Regulations (Current Edition) and the IEE
Wiring Regulations (Current Edition).
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic Gas
Installation I.S. 813 Current Editions and the
ETCI Rules for Electrical Installations.
Provision for ventilation
Detailed recommendations are contained in the
following British Standards Codes Of Practice:
B.S. 6172/B.S. 5440, Par. 2 and B.S. 6891
Current Editions.
The hob should not be installed in a bed sitting
room with a volume of less than 20 m³. If it is
installed in a room of volume less than 5 m³ an
air vent of effective area of 100 cm² is required.
If it is installed in a room of volume between 5
m³ and 10 m³ an air vent of effective area of 50
cm² is required, while if the volume exceeds 11
m³ no air vent is required.
However, if the room has a door which opens
directly to the outside no air vent is required
even if the volume is between 5 m³ and 11 m³.
If there are other fuel burning appliances in the
same room, B.S. 5440 Part 2 Current Edition,
should be consulted to determine the requisite
air vent requirements.
For appliances installed in the Republic of
Ireland please refer to the NSAI- Domestic Gas
Installation I.S. 813 Current Editions Table Four.
Location
The hob may be located in a kitchen, a kitchen/
diner or bed sitting room (with a volume greater
than 20 m³), but not in a bathroom or shower
room.
The minimum distance combustible material can
be fitted above the hob in line with the edges of
the hob is 400 mm. If it is fitted below 400 mm
a space of 50 mm must be allowed from the
edges of the hob.
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic Gas
Installation I.S 813 Current Edition Section 7-
Permitted Locations of Appliance.
10
Gas Connection
WARNING!
Any gas installation must be carried
out by a GAS SAFE REGISTER
installer.
Make sure that, once the hob is installed, it is
easily accessible for the engineer in the event of
a breakdown.
The manufacturer will not accept liability, should
the above instructions or any of the other safety
instructions incorporated in this instruction
booklet be ignored.
On the end of the shaft, which includes the G
1/2" threaded elbow, adjustment is fixed so that
the washer is fitted between the components as
shown in the diagram. Screw the parts together
without using excessive force.
A
B C
A) End of shaft with nut
B) Washer
C) Elbow
Connection to the gas supply should be with
either rigid or semi-rigid pipe, i.e. steel or
copper.
The connection should be suitable for
connecting to R 1/2 (1/2 BSP male thread).
When the final connection has been made, it is
essential that a thorough leak test is carried out
on the hob and installation.
Make sure that the main connection pipe does
not exert any strain on the hob.
If you use flexible metal pipes make sure that
they agree to ISO 10380 and ISO 10807
standards. Be careful they do not come in touch
with mobile parts or they are not squeezed. Also
be careful when the hob is put together with an
oven.
www.zanussi.com