Clarke PIONEER 210 OF Руководство по эксплуатации и техническому обслуживанию - Страница 6
Просмотреть онлайн или скачать pdf Руководство по эксплуатации и техническому обслуживанию для Воздушный компрессор Clarke PIONEER 210 OF. Clarke PIONEER 210 OF 8 страниц. Pioneer oil free compressor
Печатать страницу
OPERATING INSTRUCTIONS
Before connecting your Pioneer compressor to the mains supply, check the following:-
1.
The mains voltage is 230V.
2.
The ON/OFF control knob (D) is in the OFF (inner) position.
3.
The pressure regulator (H) should be set at its lowest setting, by pulling knob upwards
and turning it fully anticlockwise to required pressure, push back down to lock in
position.
4.
If the machine has not been used for 24 hours or so, open the air receiver drain valve
(B) and turn it on its end in order to drain any condensate which may have
accumulated. When clear, close the valve, finger tight. DO NOT rest the compressor
on the drain valve.
IMPORTANT
If the receiver is under pressure, keep your hands well away from the air being expelled....
remember, compressed air can be DANGEROUS!
Fig. 1
A
B
C
D
E
F
A.
Air Receiver
B.
Air Receiver Drain Valve
C.
Non Return Valve
D.
ON / OFF Knob
E.
Air Receiver Pressure Gauge
Connect a suitable air hose, fitted with a quick fit adaptor, to the quick fit coupling (I) on
the compressor.
On the other end of the air hose, fit the spray gun or air tool to be used, using a conventionall
¼" BSP connector and or quick fit coupling, DO NOT use snap couplings at the tool. If a
snap coupling is used, it must be connected via a whip hose.
Once the connections are complete, CHECK AGAIN to ensure the air pressure regulator
knob (I) is turned fully anticlockwise, plug the compressor into the mains supply and switch
and switch ON, switch the compressor ON by pulling the ON/Off Switch (B) out, until it clicks
into position.
The compressor will now start, and the pressure will build up in the receiver to a regulated
max, pressure of 8 bar (116 psi) the motor should then stop.
Should the motor fail to start immediately, this is probably because the receiver is already
fully charged, check the pressure gauge (E) . If you release some air, by opening the drain
valve (B), the motor should start automatically once the air pressure has dropped sufficiently,
ie; when the cut in pressure is reached.
(Figures in brackets refer to Fig. 1 below)
G
H
Fig. 2
I
F.
Mains Lead
G.
Air Receiver Specification Plate
H.
Air Pressure Regulator Knob
I.
Quick Fit Coupling
- 5 -
PARTS LIST (Pump)
Index No
Part No
1
FN116HP0001
2
FN116HP0002
3
FN116HP0003
4
FN033047000
5
FN034139000
6
FN316HP1604
7
FN033005000
8
FN116120007
9
FN014002154
10
FN014003003
11
FN116120008
12
FN015083000
13
FN014005069
14
FN033055000
15
FN416HP0004
16
FN116HP0005
17
FN116120013
18
FN014003001
19
FN416HP0007
20
FN014001056
21
FN009200004
22
FN008277000
23
FN011117000
24
FN116HP0011
25
FN116120017
26
FN116HP0008
27
FN116HP0009
PARTS LIST (Receiver)
50
FN126HB0012V
51
FN022020000
52
FN020201000
53
FN129HU0011
54
FN014013042
55
FN347043000
56
FN047113001
57
FN047113002
58
FN010041000
59
FN046001000
60
FN011017000
61
FN321028000
62
FN101GA0200
63
FN347022000
64
FN330004000
65
FN011017000
66
FN319044000
Description
Housing
Main Shaft
Crank
Bearing
Rotor
Stator
Bearing
Housing
Bolt
Nut
Fan
Circlip
Distance Piece
Bearing
Piston
Special Bolt
Gasket
Nut
Cylinder Head
Screw M8
Capacitor Compl.
Overload/Reset
Olive
Nut
Filter Element
Cover
Cover
6lt Tank
Drain Cock 3/8"
Vibration Damper
Delivery Tube
Screw M5x15
Check Valve
Seal
Spring
Gasket
Rilsan Tube
Nipple 1/4"
Pressure Switch
Power Cable With BSI Plug
Safety Valve
Pressure Gauge Ø50-1/4"
Nipple 1/4"
Pressure Reducer With Line Cock
- 10 -
Qty
1
1
1
1
1
1
1
1
3
3
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
1