Directed Xpresskit DBALL2 Руководство по установке - Страница 8

Просмотреть онлайн или скачать pdf Руководство по установке для По замкам Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 19 страниц. Ford5 remote start ready (rsr) installation
Также для Directed Xpresskit DBALL2: Руководство по установке (12 страниц), Руководство по установке (18 страниц), Руководство (14 страниц), Руководство по установке (13 страниц), Руководство по установке (14 страниц), Руководство по установке (19 страниц), Руководство по установке (16 страниц), Руководство по установке (20 страниц), Руководство по установке (15 страниц), Руководство по установке и краткому руководству (16 страниц), Руководство по установке (18 страниц), Руководство по установке (16 страниц), Руководство по установке (18 страниц), Руководство по установке (16 страниц), Руководство (19 страниц)

Печатать страницу
Directed Xpresskit DBALL2 Руководство по установке
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Module Programming
Refer to the LED Diagnostics section on page 12 for more information and for troubleshooting purposes.
Important
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL2, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning!
To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL2.
a.
To ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b.
Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL2 D2D connector.
Connect SmartStart to DBALL using the D2D port.
OR
XL202 Installation
Connect XL202 to DBALL2 using the D2D port.
Connect the 10-pin, 12-pin and 14-pin harnesses to
1
DBALL, then wait until the LED turns ON solid red.
IMPORTANT: Do NOT press the brake pedal.
2
Press the Push-To-Start (PTS) button twice to turn
the ignition ON.
The orange LED flashes then the green LED turns ON for 3 seconds
3
and shuts off.
4
Press the Push-to-Start (PTS) button once more to turn the ignition OFF.
You have successfully completed the module programming sequence.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
st
1
Do NOT
press the
brake pedal
Flashes
Rev.: 20161207
SmartStart
XL202
&
rd
3
nd
2
ENGINE
2X
PUSH
START
STOP
&
&
Solid Green or
Orange x3 sec
ENGINE
1X
PUSH
START
STOP
© 2016 Directed. All rights reserved.
Page 8
Solid
Off