Platform: DBALL2
Firmware FORD3 emote Start
:
R
Feature and Option List
It is recommended to configure all
flashing page on www.directechs.com. The web offers more options such as
features is possible using the information on this page.
* Default option
Feature
Operation
1
RF Output Type
2
Smart OEM Alarm Control
Feature Programming
To enter feature programming routine
-
Turn t
he ignition
ON
, then
-
Within 5 seconds, press and
Programming button.
-
The
LED
will flash green once slowly
the current option of feature 1
repeat until
a new command is entered
Changing feature options
-
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL
in
RSR
using 3x
change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will
change the option for the selected feature.
-
The
LED
flashes
red
rapidly the number of times equal to the current option number. After a short delay, the
the number of times to indicate the current feature.
Accessing another feature
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-
The
LED
flashes green slowly the number of times equal to the feature number. After a short delay, the
indicate the current option of the current feature.
When the maximum number of features or options is reached, the
Once a feature is programmed
-
Other features can be programmed.
-
The feature programming can be exited.
Exiting feature programming
-
No activity for 30 seconds; after 30 seconds, the
sequence.
OR
-
Press and
HOLD
the programming button for 3 seconds. After 3 seconds, the
end of the programming sequence.
Ready (R
the
features and options listed below
Flashes / Option
1. Disabled*
2. RFTD Output
3. SmartStart
1. Disabled
2. Safelock
3. Enabled*
OFF
.
HOLD
the rogramming button
p
to indicate the feature number is 1. After a short delay, the
(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence will
.
OEM
Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to
The flashing sequence will
The flashing sequence will
LED
will turn
SR Installation
)
using
the
RSR
Description
Module is connected to a remote starter using a standard installation.
Module is connected to an XL202 using an RSR or RXT installation (when
available).
Module is connected to SmartStart using an RSR or RXT installation (when
available).
The OEM alarm will not be controlled by DBALL upon remote start. No disarm
or arm command will be executed at the beginning or end of the sequence; it
must be controlled by the Remote Starter.
Smart OEM Alarm Control will behave like a standard Safelock feature on a
remote starter. It will unlock at the beginning of the sequence, and relock after
start and shutdown.
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will
disarm and rearm the vehicle in the remote start sequence, only when
required. The reason for this is, factory alarm control must often be done by
lock or unlock operation. This could create unnecessary actions on door lock
modules, such as the horn to honk. When possible, Smart OEM Alarm
Control will monitor the alarm and door lock status to detect if the disarm or
rearm is required. If the vehicle is unlocked or is not equipped with factory
alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will
also monitor the remote starter actions so that the factory alarm control is not
done twice. A remote starter, for which the Safelock feature is active, will work
perfectly with this option and will make it invisible to the user.
until the
LED
turns
ON
orange (
repeat until
repeat until
LED
will start flashing again from the first feature or option.
ON
orange for 2 seconds to confirm the end of the programming
LED
will turn
configuration tool found on the module
; however, manual configuration of the
Programming
Button
after 3 seconds . Release the
)
LED
flashes
red
rapidly to indicate
.
LED
flashes green slowly
a new command is entered
.
LED
flashes red rapidly to
a new command is entered
.
ON
orange for 2 seconds to confirm the
© 2017 Directed. All rights reserved.
Rev.: 20170908
Page 13
Печатать страницу