Directed Xpresskit DBALL2 Руководство по установке - Страница 14

Просмотреть онлайн или скачать pdf Руководство по установке для По замкам Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 15 страниц. Ford5 remote start ready (rsr) installation
Также для Directed Xpresskit DBALL2: Руководство по установке (12 страниц), Руководство по установке (19 страниц), Руководство по установке (18 страниц), Руководство (14 страниц), Руководство по установке (13 страниц), Руководство по установке (14 страниц), Руководство по установке (19 страниц), Руководство по установке (16 страниц), Руководство по установке (20 страниц), Руководство по установке и краткому руководству (16 страниц), Руководство по установке (18 страниц), Руководство по установке (16 страниц), Руководство по установке (18 страниц), Руководство по установке (16 страниц), Руководство (19 страниц)

Печатать страницу
Directed Xpresskit DBALL2 Руководство по установке

Quick Reference Guide

DBALL2-NISS06 Remote Start Ready (RSR) Installation
Vehicle Takeover with Get In and Go*
Press the remote start button on the transmitter to
1
start the vehicle.**
Press the Unlock button on the factory
2
or aftermarket remote.**
Enter the vehicle, while making sure the
3
factory remote is inside with you.
Close the door then press the brake
4
pedal, put the car in gear and drive off.
* Get In and Go connections required.
** Your aftermarket remote may differ from the model shown in the illustrations.
Get In and Go
Get In and Go is designed to provide users with easy takeover when
GG
entering their Push-to-Start (PTS) equipped vehicle, once it has been
remote started.
Typically, users would have to remote start their vehicle, then get inside and press
the vehicle start button to perform a takeover. There is therefore a physical action
required to drive away. With Get In and Go technology, you simply remote start the
vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and
enjoy your vehicle.
This unique feature monitors a variety of parameters such as the key fob, vehicle
speed sensor and door sensor, in order to perform takeover securily.
GG
Press
remote start
button**
Press Unlock
OR
button on
either remote**
Enter vehicle
with key fob
Ready to
drive off
Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand,
but wish to keep the engine running.
Stop the vehicle in a safe parking spot
1
and put the gear in Park (P).
Press the button to remote start the vehicle.*
2
The PTS button will flash once to
indicate the vehicle is now in Pit Stop
Mode.
It is now safe to leave the engine running and exit the
vehicle with the factory remote in hand.
3
Note: We recommend that you always lock the doors
of your vehicle when leaving it unattended.
* Your aftermarket remote may differ from the model shown in the illustrations.
Parking Light Error Codes
The parking lights on your vehicle will flash a specific number of times 3 seconds
following an unscheduled shutdown or failure to start. Each flashing pattern is
described below.
Flashes
Diagnostic
1
Runtime expired.
2
Over-rev shutdown.
3
Low/No RPM.
4
Transmitter shutdown.
5
Brake shutdown.
6
Hood shutdown/Remote start safety override switch is ON*.
7
Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input
will report 7 flashes.
P
&
Stop & put vehicle in Park (P)
Press
ENGINE
&
START
remote start
STOP
button*
Flashes
Exit vehicle with
Smart Key
© 2017 Directed. All rights reserved.