Clarke Woodworker VRS1 Эксплуатация и техническое обслуживание - Страница 7
Просмотреть онлайн или скачать pdf Эксплуатация и техническое обслуживание для Сандер Clarke Woodworker VRS1. Clarke Woodworker VRS1 8 страниц. Vertical reciprocating sander
Печатать страницуCHANGING SANDING SLEEVES
Ensure the machine is switched off and isolated from the power supply by removing the
plug from the 13amp socket, then proceed as follows.
To Remove Old Sleeve
1.
Grasp and hold the sanding sleeve, loosen the nut on
top of the arbor using 14mm spanner in a clockwise
direction (see Fig. 5).
2.
Slide old sanding sleeve off arbor in direction of arrow
A (see Fig. 6).
Clean sawdust accumulation from arbor and
surrounding areas.
To Fit New Sleeve
1.
Slide new sleeve onto arbor, in direction B until it is flush
with the top of the rubber cylinder.
2.
Grasp and hold the sanding sleeve as above, tighten
the nut in anticlockwise direction. Do Not Overtighten,
tighten sufficiently to hold the sleeve without slipping.
NOTE: If sanding sleeves become difficult to remove or install,
apply french chalk/talcum powder on the inside of the sleeve
before installing onto the arbor.
CHANGING ARBORS
Ensure the machine is switched off and isolated from the power supply by removing the
plug from the 13amp socket, then proceed as follows.
1.
Loosen and remove two screws (see Fig. 7).
2.
Remove front cover to expose Arbor base and
spindle (see Fig. 8).
3.
Using two 17mm open ended spanners, one on
the spindle and the other on the arbor base.
Holding the spindle, unscrew the arbor in clockwise
direction and remove, store safely.
4.
It may be necessary to change the table insert for the
chosen arbor, this is done by simply removing two
retaining screws, lift out insert, fit new insert, ensure it is lined up on
locating pin, refit retaining screws.
NOTE: it is important to fit an insert as close as possible to the
size of the arbor with sanding sleeve fitted.
4.
Select required arbor and fit in reverse order.
5.
Refit front cover and retain in place with screws
removed earlier.
WARNING
NEVER operate the sander with any covers removed.
Fig. 5
A
B
Fig. 6
Handle
Front Cover
Fig. 7
Screws
Fig. 8
-9-
ELECTRICAL CONNECTIONS
This product is fitted with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection
to a standard, domestic electrical supply. Should the plug need changing at any time,
ensure that a plug of identical specification is used.
WARNING ! THIS APPLIANCE MUST BE EARTHED
This machine must be wired up in accordance with the following colour code:
BLUE
BROWN
GREEN/YELLOW - EARTH
Connect the BLUE coloured cord to the plug terminal marked N
Connect the BROWN coloured cord to the plug terminal marked L
Connect the GREEN/YELLOW coloured cord to the plug terminal marked E
If this appliance is fitted with a plug which is moulded on
to the electric cable (i.e. non-rewireable) please note:
1.
The plug must be thrown away if it is cut from the
electric cable. There is a danger of electric shock if it
is subsequently inserted into a socket outlet.
2.
Never use the plug without the fuse cover fitted.
3.
Should you wish to replace a detachable fuse carrier, ensure that the correct
replacement is used (as indicated by marking or colour code).
4.
Replacement fuse covers can be obtained from your local dealer or most electrical
stockists.
Fuse Rating
The fuse in the plug must be replaced with one of the same rating
replacement must be approved to BS1362.
If in doubt, consult a qualified electrician. Do not attempt any electrical repairs yourself.
Cable Extension
Always use an approved cable extension suitable for the power rating of this tool (see
specifications), the conductor size should also be at least the same size as that on the
machine, or larger. When using a cable reel, always unwind the cable completely.
IMPORT ANT:
If a cable extension is needed, it is essential to comply with the following data.
Voltage
Extension length
230v
230v
From 20 to 50m
- NEUTRAL
- LIVE
(13 amps)
Cable section
2
Up to 20m
2.5mm
2
4mm
-6-
and this