Directed Electronics SmartStart 5000-series Руководство пользователя - Страница 4
Просмотреть онлайн или скачать pdf Руководство пользователя для Автомобильная сигнализация Directed Electronics SmartStart 5000-series. Directed Electronics SmartStart 5000-series 6 страниц.
Также для Directed Electronics SmartStart 5000-series: Краткое руководство по установке (2 страниц)
Печатать страницу
3. Install the VSM200/250 or DSM200/250 using
the information in the wiring diagram and steps
(Note CAUTIONS during installation).
a. Configuration Wires: Connect the loose gray
or white configuration wire(s) to match the
desired application (see table below).
MODE
ESP2
D2D, RSR/RXT
Autostart/AstroStart
b. Connect the serial data cable and adapter to
the correct port of the main module. For D2D
RSR/RXT applications, connect the serial
data cable and adapter to Xpresskit module.
c. Complete the main power connections.
d. When power is connected, the module be-
gins an initialization procedure that may
take several minutes. During this procedure,
progress is reported via the flashing Amber/
Green LEDs next to the module cable. When
both LEDs turn on solid, the initialization pro-
cedure is completed (See Status LEDs for a
description of the various LED states).
4. Verify and Activate the SmartStart module:
The following steps need to be performed for the
Verification/Activation of the Directed SmartStart
module.
a. Collect Customer Information:
Customer's Full Name:
Customer's E-mail Address:
Customer's mobile phone # and phone carrier
Record/place Module ID # here:
New Account:
If this is an existing account, are you:
adding a new system:
or replacing an existing one:
2
GRAY WIRE
WHITE WIRE
Open
Open
GND
Open
Open
GND
Existing Account:
b. Log on to: www.directechs.com, and click on
the SmartStart link.
c. Follow the on-screen directions to activate
and test a SmartStart device. If this is the cus-
tomer's first SmartStart system, you will be
prompted to enter their information as col-
lected in step 4a.
d. Set configuration for commands to match the
installed application.
e. Test the SmartStart system from the website
using the supplied function links.
f.
The customer is sent log-in information via
e-mail. After logging into the site at www.
mysmartstart.com, they must select and pay
for the service plan in order to start using the
system.
Status LEDs
Amber LED states:
•
Off: No cellular communication. Check
connections such as module harness.
•
Flashing slowly: The module is seeking
cellular system communication.
If no cell coverage is available the Amber
LED continues to flash slowly, move the
vehicle to a location with better reception.
•
Flashing quickly: The module is negotiat-
ing with a cellular system.
•
On solid: Communication successfully es-
tablished.
Green LED states:
•
Off: Communication not established with
the remote start main unit or no serial de-
vice is connected.
Check connection at the Bitwriter port,
once connected properly the LED turns on
after resetting the power to the SmartStart
module.
•
On solid: Communication successfully es-
tablished with the remote start main unit.
Please return this guide and point the customer to
steps 4a and 4f after successfully completing the in-
stallation as it contains details required for account
setup.
Notes: SmartStart response time can vary depend-
ing on cellular coverage and network congestion.
Operating temperature range: -30°C to + 70°C.
Additional information
can be found at:
www.directechs.com
Directed Logo Usage
Logo, Directed with designed in USA.eps
Logo, Directed Electronics w-driven.eps
© 2011 Directed Electronics. All rights reserved.
Logo, Directed with Distributed By.eps