Alemite 586-B Инструкции по эксплуатации и техническому обслуживанию - Страница 9
Просмотреть онлайн или скачать pdf Инструкции по эксплуатации и техническому обслуживанию для Инструменты Alemite 586-B. Alemite 586-B 12 страниц. Cordless grease gun (battery charger included)
Также для Alemite 586-B: Инструкции по эксплуатации и техническому обслуживанию (16 страниц)
Печатать страницу
Priming the gun
In most cases the gun will prime simply by
operating the trigger several times.
Should grease fail to appear, air must be
bled.
Force prime
This process manually assists air within the
gun to be bled at the bleed valve.
1 Pull the follower rod and engage the
follower by rotating the rod.
2 Depress bleed valve (45) and at the same
time push on the follower rod.
Once the air is eliminated, operate the gun
several times.
Once grease appears, disengage the
follower rod from the follower and push into
the grease cylinder.
Check valve contamination
Should the gun fail to prime; the outlet
check may be held open. Remove plug (36),
clean ball (38), and the ball seat of head (14).
Gun operation
Battery (41) is intentionally shipped with a
low charge. Charge the battery prior to use.
Refer to the battery charger operation
section for details.
CAUTION
The gun is equipped with software to
protect the motor. When a blocked
bearing, line, or grease fitting causes the
gun to stall, the software will cut power
to the motor. If this situation occurs,
release the trigger immediately.
For maximum motor life, avoid
operating at stall.
Battery and Charger Safety
Rules
This manual contains important safety and
operating instructions for battery part
number 343432 and battery chargers
343500 and 343501.
WARNING
Before using the battery charger read all
instructions and cautionary markings
on battery charger (42, 43),
battery (41), and products using the
battery.
An extension cord should not be used
unless absolutely necessary. Use of an
improper extension cord could result in
a risk of fire and electric shock. If an
extension cord must be used, make sure
it is 18- gauge. Check to ensure that the
pins on the plug of the extension cord
are the same number, size, and shape
as those of the plug on the charger.
Make sure that the extension cord is
properly wired and in good electrical
condition.
Do not incinerate the battery, even if it
is severely damaged or completely worn
out. The battery may explode in fire.
Risk of electric shock 120 V AC or
230 V AC present at charfer terminals.
Do not expose battery to spark or
flame. Battery liquid may burn.
Do not splash or immerse in water or
other liquids. This may cause premature
cell failure.
Never attempt to open the battery
pack for any reason. If the plastic bag of
the battery pack breaks or cracks, return
to a service center for recycling.
Failure to comply may result in death
or serious injury.
9
CAUTION
Do not expose the charger to rain, snow,
or frost.
Make sure the cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or
stress.
Do not operate the charger with
damaged cord or plug.
Replace immediately.
Do not operate the charger if it has
received a sharp blow, been dropped, or
otherwise damaged in any way.
Do not disassemble the charger.
The charger is designed to operate on
standard household electrical power.
Do not attempt to use it on any other
voltage.
Consecutive charging may cause
overheating. If you need to recharge the
battery consecutively, wait for
15 minutes to allow the charger to cool.
Do not insert foreign material into the
slot for the battery in the charger stand.
Do not disassemble the battery.
Do not store the gun and battery
assembly in locations where the
temperature may reach or exceed
104° F (40° C).
Do not short-circuit the battery.
Do not place the charger in an area of
extreme heat or cold. It works best at
normal room temperature.