Clarke CLARKE20DS Руководство - Страница 3
Просмотреть онлайн или скачать pdf Руководство для Напольная машина Clarke CLARKE20DS. Clarke CLARKE20DS 13 страниц.
Печатать страницу
OPERATION OF FLOOR MACHINE
READ OPERATORS MANUAL THOROUGHLY PRIOR TO OPERATING OR SERVICING THIS MACHINE.
GENERAL USE
1.
Remove any obstructions or other obstacles in the area which is to be cleaned.
2.
Place the handle in the upright position and tilt machine back until handle rests on the fl oor
* Be sure the machine is not plugged into an outlet
3.
Attach the pad driver or brush to the machine by placing the clutch plate over the gearbox hub and turning the driver / brush 1/4 turn.
4.
Place machine back into its upright position.
5.
Plug power cord into a grounded outlet. NOTE: Never use an extension cord in conjunction with the standard power cord.
6.
The handle height may be adjusted by lifting up the compression handle which is located on the right side of the handle tube about 1 foot above
fl oor level. Release the compression handle and adjust handle to safe operating height, then push back down on the compression handle to lock the
handle in operating position.
7.
Select either low speed (185rpm) or high speed (330rpm) by pushing the motor mounted switch into the low or high position. NOTE: Never change
the speed while operating the machine. Be sure the power is turned off prior to changing the speed.
8.
To start the machine, press the red safety button on the top of the upper switch housing, and then squeeze either of the operating triggers. (the safety
button must be depressed prior to squeezing the operating triggers.)
9.
When the machine is in operation, both hands should be placed on the switch housing (upper handle).
10. During operation, to make the machine go right, gently raise the handle. To make the machine to left, gently lower the handle.
11. To stop the machine at any time, simply release the operating trigger [s] and the machine will stop automatically.
MAINTENANCE
To keep this machine performing well for many years, please follow the following maintenance procedures:
Always confi rm the machine is unplugged from the power source prior to performing any maintenance or repairs!
1.
Unplug machine as soon as you are done using it.
2.
Tilt machine back and remove pad driver or brush.
* Never store a low speed machine with the pad driver or brush mounted to the machine
3.
Clean the outside of the machine with a mild cleaner.
4.
Check power cord for any damage. If damage is detected, replace power cord immediately.
5.
Lubricate wheels with a water resistant lubricant once a month.
6.
Check machine for loose or missing nuts and bolts, and replace as necessary.
7.
If the machine is used in a dusty environment, you may remove the motor cover and blow the motor clean with compressed air. This will ensure
proper ventilation, and allow the motor to run cooler.
STORAGE
1.
Unplug machine from power source and wrap cord on handle.
2.
Tilt machine back and remove pad driver or brush.
3.
Store machine in upright position and in a dry area.
HANDLE RELEASE ASSEMBLY INSTRUCTIONS
STEP 1
1)
Remove nut and spacer from handle bracket assembly.
2)
Push the two handle brackets backward so they lay on the fl oor.
STEP 2
1)
Remove Handle Clamp Blocks with 5mm hex head.
2)
Place handle assembly into handle clamp blocks.
3)
Re-attach the blocks to the base with 5mm hex head.
STEP 3
1)
Make sure actual cord wrap faces to the left of the machine when
you are standing behind it.
2)
Assemble hardware in the following order: spacer, left handle
bracket, nylock nut. (Do not over tighten nylock nut. Only tighten it
enough to hold handle in place when compression lever is in down
position).
STEP 4
1)
Connect Power Cords together
2)
Connect Power Cord Covers together.
7/2014
INSTRUCTIONS FOR USE
4
56091129 - CFP Pro 20DS
ENGLISH - A
3
2
1
A - 3