Cub Cadet 190-341-100 Руководство по установке и обслуживанию - Страница 18

Просмотреть онлайн или скачать pdf Руководство по установке и обслуживанию для Снегоуборщик Cub Cadet 190-341-100. Cub Cadet 190-341-100 20 страниц. 42" snow thrower attachment for cub cadet series 2000/2500 tractors
Также для Cub Cadet 190-341-100: Руководство по эксплуатации (20 страниц)

Печатать страницу

Cub Cadet 190-341-100 Руководство по установке и обслуживанию

A. DURING SEASONAL USE.

This section describes maintenance procedures

designed to keep your snow thrower in good

operating condition.

Shave Plate And Skid Shoes

The shave plate and skid shoes on the bottom of the

snow thrower housing are subject to wear. They should

be periodically checked for wear and replaced when

necessary. Failure to do so will result in damage to the

housing. Refer to Figure 30.

1. Replace the shave plate as follows:

a. Remove the six hex nuts, bell washers, and

carriage bolts that secure the shave plate to

the bottom of the housing.

b. Remove the rear most hex nut, bell washer,

flat washer and carriage bolt securing the back

end of each skid shoe to the sides of the

housing. Loosen the four remaining hex nuts

that secure the skid shoes to the housing.

c. Slide the shave plate out of the off-set slot at

the bottom of the housing, and from between

the skid shoes and side panels of the housing.

d. With the mounting holes toward the back, slide

the new shave plate into position. Loosely in-

stall the six carriage bolts, bell washers, and

hex nuts fastening the shave plate to the bot-

tom of the housing.

e. Insert the carriage bolts through the rear of

skid shoes and the ends of the shave plate

and the install the flat washers, bell washers,

and hex nuts removed earlier.

Reposition the skid shoes and fully tighten the

fasteners securing the skid shoes to the hous-

ing. Fully tighten the fasteners securing the

shave plate.

2. The skid shoes are reversible for longer life. Re-

move the hex nuts, flat washers, bell washers and

carriage bolts fastening the skid shoes to the hous-

ing. Turn the shoes over and/or reverse sides to

ensure even wear and extend their service life.

Augers

1. The augers are secured to the auger shaft with six

shear pins and bow-tie cotter pins. Refer to Figure

26. If an auger is suddenly jammed by a foreign

object or ice chunk, the pin is designed to shear —

minimizing potential damage to the gear box or

sprocket box.

SECTION V. MAINTENANCE

2. If the augers will not turn, check the pins to see if

Lubrication

1. The auger gear box is lubricated with grease at the

2. The sprocket box assembly is also neither

3. The right angle gear box is not servicable and

4. Apply penetrating oil to the cables of the chute tilt

5. Apply a good grade of spray lubricant to the univer-

they have sheared. Two replacement shear pins

(5) and bow-tie cotter pins (12) have been provid-

ed with the snow thrower. For future use, order

part number 738-04124A for replacement shear

pins and 714-04040 for the bow-tie cotter pins.

AUGER

GEAR BOX

SHEAR PIN

& BOW TIE

COTTER PIN

SKID SHOE

Figure 30

factory and is neither externally servicable, nor re-

quires checking. If disassembled for any reason,

lubricate with 2 ounces (by weight) of Shell Alvania

grease, part number 737-0168. Before reassem-

bling, remove all old sealant and apply Loctite Ul-

tra Grey (759-3746) sealant, or equivalent, to the

housing halves.

externally servicable, nor requires checking. If

disassembled for any reason, lubricate with 5.0

ounces (by weight) of Benalene grease, part

number 737-0300A. Before reassembling, remove

old sealant and apply Loctite Ultra Grey (759-

3746) sealant or equivalent.

should not be disassembled.

handle assembly at least once a season.

sal joints of the chute crank, and to the pivot of the

chute tilt handle at least once a season.

SKID

SHOE

CARRIAGE

BOLTS

BELL WASHER

& HEX NUT

SHAVE

PLATE