Blagdon Pump X25 Руководство по обслуживанию и эксплуатации - Страница 14
Просмотреть онлайн или скачать pdf Руководство по обслуживанию и эксплуатации для Водяной насос Blagdon Pump X25. Blagdon Pump X25 16 страниц. Air operated double diaphragm pump
Также для Blagdon Pump X25: Руководство по обслуживанию и эксплуатации (12 страниц)
Печатать страницуThe format of the Wet-Side kit part number is broken down as shown below. The number always starts with 'SA' followed by the model
number, diaphragm letter, ball valve letter and pump material. If rubber seats are used, an 'R' is added to the end. A 'W' is added fol-
lowing the ball valve letter if pump is fitted with weighted balls. These are not available for sizes below 1".
If pump model number includes a revision number then this is added where shown below. Please refer to either the pump nameplate
or the operating manual provided with the pump if this is to be included, i.e. B0601SSBBTTS
NOTE! This part number system does not apply to pumps designated :-
B4001, B5001 or B7501. Please consult the pump Service & Operating Manuals for Wet-Side Kit numbers for these models.
If in doubt please consult Sales at Blagdon Pump.
TYPICAL CODE =
PART NUMBER :-
SA : ALL KITS
MODEL NUMBER :
Pump Type i.e:- 06, 15 , 1H , 1A , 25 ,
40, 1B , 2B , 50 , 1C.
DESIGN REVISION :
SEQUENTIAL NUMBER STARTING AT 00
(NOT USED IF MODEL HAS NOT BEEN
REDESIGNED SINCE DEC. 1999)
I.E. SA15BBNR
(SEE NOTE ABOVE)
DIAPHRAGMS :
B : BUNA-N
E : EPDM
H : POLYESTER
N : NEOPRENE
O : ONE PIECE PTFE
The following details refer to the main recommended spares kits available for your Blagdon Pump. Not all combinations and trim
options are listed here. Please refer to your local stockist / distributor if you require further details or availability of other kits.
- Air Side Kits -
SA10515 - Standard Air side kit. All pumps are Lube Free as standard. If lubrication is used inadvertently this will not
damage the pump in any way.
Note! This kit is identical to SA10415 but without the 8 G339 O-Rings.
- Valve Block Sub-Assemblies -
SA10463 - BSP
SA10465 - NPT
- Wet Side Kits - SA2500TTN
- Filter / Regulator SA10444
- Filter/Regulator/Lubricator - FRL
HG-CF-1101 Rev. C – 19.05.06
Wet Side Kit Structure
Diaphragm Pump Wet-Side Kits - Part Number Structure
SA 25 00 N N M R
P : POLYURETHANE
R : SANTOPRENE
T : PTFE
V : VITON
X : HIGH TEMP.
SA10378
VALVE SEAT MATERIAL / 2:1 OPTION :
R : RUBBER OPTIONS
(ONLY USED IF PUMP TRIMMED WITH
RUBBER SEATS)
1 : HIGH PRESSURE (W1 MODELS)
PUMP BODY / BALL VALVE MATERIAL :
M : METALLIC
N : NON-METALLIC
S : 1/2" STAINLESS STEEL
W : WEIGHTED VALVE BALL
Z : HYGIENIC MODELS
VALVE BALLS :
B : BUNA-N
D : DELRIN (ACETAL)
E : EPDM
N : NEOPRENE
Spares Kits
S : 316 ST. STEEL
T : PTFE
V : VITON
Page 14