ARO ARO PH10A-ASS-SST Руководство по эксплуатации - Страница 6

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Водяной насос ARO ARO PH10A-ASS-SST. ARO ARO PH10A-ASS-SST 9 страниц. 1” high pressure diaphragm pump 3:1 ratio (metallic)
Также для ARO ARO PH10A-ASS-SST: Руководство по эксплуатации (9 страниц)

ARO ARO PH10A-ASS-SST Руководство по эксплуатации
PARTS LIST / PH10A-XXX-XXX AIR MOTOR SECTION
n Indicates parts included in 637338 Air Section Repair Kit.
Item
Description
(size)
101 Motor Center Body
102 "O" Ring
n
(1/16" x 1" o.d.)
V 103 Sleeve
104 Plate
109 Piston
110 "U" Cup
n
(3/16" x 1-3/8" o.d.)
111 Spool
112 Washer
(1.556" o.d.)
113 "O" Ring
n
(small) (1/8" x 1-1/4" o.d.)
114 "O" Ring
n
(large) (3/32" x 1-9/16" o.d.)
115 Spacer
116 Spacer
V 118 Actuator Pin
V 121 Plug
123 Button Head Screw
(M6 x 1 x 12 mm)
124 Tie Rod
125 Dowel Pin
(5/16" o.d. x 5/8")
126 Pipe Plug
(1/8 - 27 NPT.)
127 Street Elbow
136 Plug
137 "O" Ring
n
(1/16" x 1-7/8" o.d.)
148 Piston Assembly
149 Adapter Piston
V "Smart Parts", keep these items on hand in addition to the service kits for fast repair and reduction of down time.
L
Indicates parts included in 637339--( ) fluid section service kit.
MATERIAL CODE
[A] = Aluminum
[C] = Carbon Steel
[B] = Nitrile
[D] = Acetal
[Br] = Brass
[Fg] = Fiberglas
[Bz] = Bronze
[SH] = Hard Stainless Steel
AIR SECTION SERVICE
Service is divided into two parts - - 1. Pilot Valve, 2. Major Valve.
GENERAL SERVICE NOTES:
S
Air Motor Section Service is continued from step 8 of the Fluid Sec-
tion Disassembly.
S
It is not necessary to remove the Fluid Section Ends to gain access
to the Air Motor Major Valve Section.
S
In most cases, problems of an air control nature will reside in the Air
Valve area.
S
Removal of the Fluid Sections is required to install all of the parts in-
cluded in the Air Section Service Kit, if this is the case, follow steps 1
thru 8 of the Fluid Section Disassembly on both sides and isolate the
Air Section.
S
SERVICE KIT NOTE: Only two replacement "O" rings are supplied
j
in the 637338 and 637339-( ) kits.

PILOT VALVE DISASSEMBLY

S
NOTE: Both outer pump Fluid Sections must be removed to access
the Pilot Section parts (see figure 3, page 7).
1. Remove two (123) screws and (104) plate from both sides of the
(101) motor center body.
Page 6 of 8
Qty Part No.
Mtl
(1)
95122-1
[A]
(2)
Y325-20
[B]
(1)
94527
[D]
(2)
95125
[SS]
(1)
92011
[D]
(1)
Y186-51
[B]
(1)
92005
[A]
(5)
92877
[Z]
(5)
Y325-214
[B]
(6)
Y325-126
[B]
(4)
92876
[Z]
(1)
92006
[Z]
(2)
95126
[SS]
(2)
95123
[D]
(4)
95176
[C]
(8)
95195
[SH]
(2)
Y148-45
[C]
(10) Y227-2-L
[C]
(1)
94763
[Br]
(2)
94075
[SS]
(2)
Y325-31
[B]
(2)
61419
[B]
(2)
94073-1
[C]
2. A light tap on (118) actuator pin should expose the opposite (121)
[SS] = Stainless Steel
3. Remove (170) piston sleeve and inspect the inner bore for damage.
[T] = PTFE
[U] = Polyurethane
[Z] = Zinc
S
1. Assemble the trailing (102) "O" ring to (103) sleeve and assemble
2. Assemble (102) "O" ring to (103) sleeve and push sleeve onto motor
3. Assemble (2) "O" ring to (1) rod and assemble into (103) sleeve.
4. Assemble (171 and 172) "O" rings to (170) piston sleeve and as-
5. Assemble two (168) "O" rings and (169) "U" cup to (167) pilot piston
6. Assemble (173) "O" rings and (174) "U" cups (note lip direction) to
7. Assemble (118) actuator pins to (121) plugs and assemble (121)
8. Assemble (104) plates to (101) center body, securing with (123)
9. Reassemble fluid section parts.
Item
Description
(size)
150 "O" Ring
n
(1/16" x 1-3/16" o.d.)
V 151 Nut
152 Cylinder
153 "O" Ring
(1/8" x 6-1/2" o.d.)
nL
154 Auxiliary Body - - Right
155 Auxiliary Body - - Left
158 Cap Screw
(M8 x 1.25 x 25 mm)
159 "O" Ring
n
(1/16" x 7/16" o.d.)
163 Bushing
164 Back-Up Ring
(3/4" i.d. x 1" o.d.)
nL
165 Quad Ring
nL
167 Pilot Piston
n
(includes 168 and 169)
168 "O" Ring
(3/32" x 5/8" o.d.)
169 "U" Cup
(1/8" x 7/8" o.d.)
170 Piston Sleeve
171 "O" Ring
n
(3/32" x 1-1/8" o.d.)
172 "O" Ring
n
(1/16" x 1-1/8" o.d.)
173 "O" Ring
n
(3/32" x 1-3/8" o.d.)
174 "U" Cup
n
(1/8" x 1/2" o.d.)
201 Muffler
L Key-Lube "O" Ring Lubricant
n
10 Pack Key-Lube Grease
plug and (167) pilot piston.

PILOT VALVE REASSEMBLY

Lubricate all soft parts, spool and bores with Key-Lube grease upon
reassembly.
sleeve into motor center body, pushing thru far enough to expose
"O" ring groove on opposite end.
center body.
semble into (101) center body. NOTE: Assemble sleeve with small
i.d. into center body.
(note the lip direction of "U" cup) and assemble into (170) piston
sleeve.
(121) plugs.
plugs into (101) center body.
screws.
Qty Part No.
Mtl
(2)
Y325-23
[B]
(2)
94072
[C]
(2)
94801
[Fg]
Y325-259
[B]
(6)
j
(1)
94750-1
[A]
(1)
94751-1
[A]
(4)
95177
[SS]
(2)
Y325-11
[B]
(2)
94053
[Bz]
(4)
Y118-210
[T]
(2)
94050
[B]
(1)
67164
[D]
(2)
94433
[U]
(1)
Y240-9
[B]
(1)
94081
[D]
(1)
Y325-119
[B]
(1)
Y325-22
[B]
(2)
Y325-123
[B]
(2)
Y186-43
[B]
(1)
93110
[C]
(1)
93706-1
637175
PH10A-XXX-XXX (en)