ARO 2200 Series Руководство по эксплуатации - Страница 6
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Сверло ARO 2200 Series. ARO 2200 Series 8 страниц. 325 r.p.m.
Печатать страницуDISASSEMBLY/ASSEMBLY
INSTRUCTIONS
Never apply excessive pressure by a holding device which
may cause distortion of a part.
Apply pressure evenly to parts which have a press fit.
Apply even pressure to the bearing race that will be press
fitted to the mating part.
Use correct tools and fixtures when servicing this tool.
Don't damage "0" rings when servicing this tool.
Use only genuine ARO replacement parts for this tool. When
ordering, specify part number, description, tool model number
and serial number.
DRIVE GEARING DISASSEMBLY
Clamp tool in a smooth face vise, clamping on housing (16).
Place a wrench on adapter body (64) and strike wrench a
sharp blow to loosen adapter body.
Remove adapter body (64) and spacer (62).
Using wrenches on flats of nose housing (60) and ring gear
(46) unthread and remove drive gearing.
Remove nose housing (60) and seal (59) from ring gear.
Grasp ring gear (58) in one hand and tap threaded end of
spindle (53) with a soft face hammer; spindle and components
will loosen from ring gear.
Do not disassemble further unless damage is evident, as Brin-
elling of the bearing races may occur, making replacement
necessary.
To disassemble, remove bearing (55).
Turn snap ring (54) so the open portion allows removal of shaft
(50).
Remove shaft (50) releasing gear (52).
Repeat for removal of opposite shaft and gear.
Place shafts (50) into spindle and alternately tap ends to re-
move bearing (49).
DRIVE GEARING ASSEMBLY
Assemble snap ring (54) to groove in spindle, aligning open
portion of snap ring with hole for shaft.
Lubricate needle bearings (51) with ARO 33153 grease and
assemble to gears (52).
Lubricate gears (52) liberally with ARO 33153 grease and as-
semble one gear to spindle, securing with shaft (56).
Repeat for opposite shaft and gear.
After assembly of gears and shafts, turn snap ring so open
portion is approximately 90° from either shaft.
Assemble bearing (55) to spindle, pressing on inner race of
bearing.
Pack bearing (49) with ARO 33153 grease and assemble to
spindle, pressing on inner race of bearing.
Assemble washer (57) wave washer (56) and spindle and
components into ring gear (58).
Assemble seal (59) and nose housing (60) to ring gear (56).
Assemble drive gearing to tool and tighten, using wrenches
on flats of nose housing (68) and ring gear (46).
Assemble spacer (62) and adapter body (64) to spindle.
Assemble locking pin (65) to adapter body (64) securing with
rubber insert (66).
AUXILIARY GEARING DISASSEMBLY
Remove drive gearing from tool.
Using a wrench on flats of lock nut (37) loosen lock nut and
remove auxiliary gearing from tool.
Grasp ring gear in one hand and tap drive end of spindle with a
soft face hammer; spindle and components will loosen from
ring gear.
Do not disassemble further unless damage is evident, as Brin-
elling of the bearing races may occur, making replacement
necessary.
To disassemble, remove bearing (44).
Turn snap ring (43) so the open portion allows the removal of
shaft (39).
Remove shaft (39). releasing gear (41).
Repeat for removal of opposite shaft and gear.
Place shafts (39) into spindle and alternately tap ends to re-
move bearing (38).
AUXILIARY GEARING ASSEMBLY
Assemble snap ring (43) to groove in spindle, aligning open
portion of snap ring with hole for shaft,
Lubricate needle bearings (40) with ARO 33153 grease and
assemble to gears (41).
Lubricate gears liberally with ARO 33153 grease and as-
semble one gear to spindle, securing with shaft (39).
Repeat for opposite shaft and gear.
After assembly of gears and shafts, turn snap ring so open
portion is approximately 90° from either shaft.
Pack bearings (44 and 38) with ARO 33153 grease and as-
semble to spindle, pressing on inner race of bearings.
Assemble spindle and components into ring gear.
Thread lock nut (37) all the way onto ring gear.
Assemble auxiliary gearing to tool and tighten, using a wrench
on flats of ring gear.
Tighten lock nut (37) against housing (16) securing auxiliary
gearing.
Assemble drive gearing to tool.
MOTOR DISASSEMBLY
Remove gearing from tool.
Remove spacers (36 and 35) and motor assembly from hous-
ing (16).
Using a spanner type wrench, remove nut (23) from end plate
(26).
Grasp cylinder in one hand and tap splined end with a soft face
hammer; motor will come apart,
Remove sems fastener (24) releasing bearing (25) and end
plate (26).
MOTOR ASSEMBLY
Pack bearings with ARO 33153 grease.
Assemble bearing (25) to end plate (26) pressing on outer
race of bearing. NOTE: Assemble bearing to end plate with
the identification markings facing out.
Assemble spacer (27) and end plate (26) to rotor, pressing on
inner race of bearing.
Assemble sems fastener (24) to rotor, securing bearing and
end plate. Torque fastener to 28 in. Ibs.
Coat five rotor blades (29) with ARO 29665 spindle oil and as-
semble to rotor slots - straight side out.
Coat i.d. of cylinder (31) with ARO 29685 spindle oil and as-
semble over rotor, aligning roll pin (30) with hole in end plate.
Assemble bearing (33) to end plate (32) pressing on outer
race of bearing.
Assemble end plate (32) to cylinder, pressing on inner race of
beating.
Assemble nut (23) to end plate (26) and tighten, using a span-
ner type wrench. Torque to 9 - 12 ft Ibs.
Be sure rotor does not bind.
Assemble motor assembly and spacers (35 and 36) to hous-
ing (16).
Assemble gearing assemblies to tool.
HOUSING DISASSEMBLY
Remove snap ring (1). releasing regulator valve (3) and "0"
rings (2).
Remove regulator body (4), screen (6), inlet adapter (7), "0"
ring (8) insert (10) and spring (11).