Alto-Shaam 1000-TH-I/HD/D Инструкции по установке, эксплуатации и техническому обслуживанию - Страница 3
Просмотреть онлайн или скачать pdf Инструкции по установке, эксплуатации и техническому обслуживанию для Печь Alto-Shaam 1000-TH-I/HD/D. Alto-Shaam 1000-TH-I/HD/D 16 страниц. Low temperature oven cook hold
Печатать страницу
Unpacking and Setup
The Alto-Shaam Cooking and Holding
Oven has been thoroughly tested, checked for
calibration, and inspected to ensure only the
highest quality oven is provided. When you
receive your oven, check for any possible
shipping damage and report it at once to the
delivering carrier.
(See Transportation Damage
and Claims section of this manual.)
The oven, complete with unattached items
and accessories, may be delivered in one or more packages.
Check to insure that all the following items have been
received with each standard unit:
2 Ea. Drip Pans
4 Ea. Oven Side Racks
6 Ea. Wire Shelves
The heavy duty models have the full perimeter bumper
and casters installed at the factory.
Save all the information and instructions packed inside
the oven. Complete and return the warranty card to the
factory as soon as possible to insure prompt service in the
event of a warranty parts and labor claim.
Note: Any and all claims for warranty must include the
full model and serial number of the unit.
This cook and hold oven is designed for the purpose of
heating food to its proper temperature and maintaining the
hot food at a temperature for safe consumption. It must be
installed in a location that will permit it to function for its
intended purpose and allow adequate access for proper
cleaning and maintenance.
Oven Characteristics
The oven is equipped with a special, high-heat-density,
heating cable. Through the Halo Heat concept, the heating
cable is mounted against the walls of the cooking cavity to
provide an evenly applied heat source controlled by a
thermostat. The design and operational characteristics of
the oven eliminates the need for a moisture pan or a heat
circulating fan. Through even heat application, the quality
of a food product is maintained up to several hours.
Cold food for rethermalization or reheating
must never be added to the oven while hot
food is being held.
At no time should the oven be steamed cleaned,
washed down, or flooded with water or liquid
solution. Do not use water jet to clean. Severe
damage or electrical hazard could result.
Disconnect oven from power source before
cleaning or servicing.
Start-Up
For the best service, the oven should be installed level. The oven should NOT be installed in any area where it may be
affected by steam, grease, dripping water, high temperatures or any other severely adverse conditions.
1. Before operating the oven, clean both the interior and exterior of the unit with a damp cloth and mild soap solution.
Rinse carefully.
2. Install the external drip tray on the lower front of the oven. See installation instructions located in this manual.
3. Clean and install the oven side racks and oven shelves. Shelves should be positioned with the curved end up and
toward the back of the oven. Insert the drip pan on the interior bottom surface of the oven.
4. Before operating the unit with product, become familiar with the operation of the controls. Read the following
"General Operation" section of this manual and operate the various control functions.
I N S TA L L AT I O N
®
1 Ea. External Drip Tray
4 Ea. Casters
16 Ea. Caster Mtg. Screws
# 8 3 7 A O & C M A N U A L • 1 0 0 0 - T H - I F A M I L Y
Electrical Installation
1.An identification tag is permanently mounted on
the oven.
2.All models at 208/240 volts are dual rated units with a
conversion switch mounted under an access cover on the
rear of the oven, near the power cord.
With the voltage conversion switch in the 200 volt
through 208 volt (UPPER) position, the oven will
function properly with a source voltage of between 200
volts and 208 volts.
With the voltage conversion switch in the 220-240 volt
(LOWER) position, the unit will function properly with a
source voltage of between 220 volts and 240 volts.
NOTE:
All 208/240 volt units are shipped from the
factory with the voltage conversion switch in the
220-240 volt position. Again, ensure that the
voltage conversion switch position and the
available power source match.
3. If necessary, a proper receptacle or outlet must be
installed by a licensed electrician in accordance with
applicable local electrical codes. This oven must be
grounded in accordance with the requirements of
the National Electrical Code or applicable local
country codes.
Ensure power source matches voltage
stamped on oven nameplate.
P G . 1
SAMPLE
PH
3521030
PATENT NOS.
4595247
®