DIW RSW864T2 Руководство - Страница 2

Просмотреть онлайн или скачать pdf Руководство для Передатчик DIW RSW864T2. DIW RSW864T2 2 страницы. Wireless wall transmitter

Печатать страницу

operation manual

„DIW-Funk"- Wand-Sender

Sender: DWS-10T, DWS-20T, DWS-11, DWS-22

Intended Use:The radio wall transmitters DWS-10T/-20T/-11/-22 are radio transmitters and can

wirelessly switch suitable radio_receivers on and off or dim them. The DWS-10T/-20T models also

have a countdown timer for each channel, which can switch off the receiver after the set time. There

are 5 time options, 15s/60s/180s/30m/60m. Of course you can also set it without a timer or switch it

off manually at any time during the time. The DWS-20T model with two channels allows you to adjust

each channel separately. The DWS-11 (1 channel) and DWS-22 (2 channels) models do not have a

timer. Depending on the device, the outdoor range is up to 50 m.The wireless wall switches are

only intended for use in dry interior rooms.However, a weatherproof housing is available (DBOX-

54).

---------------------------------------------------------------------------------------------------------------------------------

Installation and connection:

- carefully pry off the front cover of the wireless wall

switch (e.g. with a screwdriver) and remove it

(Image DWS-10T left | DWS-22 right).

wall switch with 4

- Drill the holes for

- Fasten the

material.

Insert a 3V battery (type: CR2032) into the battery

compartment of the wireless wall switch, making sure that

the polarity "+" is at the top.

Attach the front panel to the wireless wall switch.

=> this is how you pair a radio receiver with the wall transmitter:

1.) Normally turn on the receiver or press and hold the receiver's learning button for 3 seconds to put

the receiver into learning status (LED flashes)

2.) then press and hold the "I" button on the transmitter for 3 seconds until the LED stops flashing

and stays on. Some receivers confirm the teach-in with a short switch.

With the wall transmitters with 2 channels, 2 different receivers can be programmed.

If you want to train additional receivers, start again at point 1.

Erasing the code

The transmitter does not store the code, but it can help erase the code from the receivers.

To put the receivers in learning status (LED flashing), press and hold the transmitter "O" (OFF) button

for 3 seconds until the LED stops flashing and stays solid, the code has been successfully erased.

Some receivers confirm the deletion with a short switch.

Since there are different receivers, it is always better to use the operating instructions for the

respective receiver for pairing and deleting.

The dimming function of the wireless wall switch with a suitable dimmer receiver:

- Press the "I" button to switch on the light in the last saved brightness.

(RSW864T1/T2 | RSW892T1/T2)

Remove the mounting plate. The

mounting plate for the wireless wall

switch is attached to the electronic part of the wireless

clips.

the attachment.

mounting plate to the wall with suitable fastening

- Press the "I" button again, the light gets darker and brighter again until

press "I" again. This new brightness is then stored.

- If you press "0", the light goes out, but the last brightness level remains saved.

=> this is how you set the timer on the wall transmitter:

(DWS-10T and DWS-20T models only)

Step 1 Put the transmitter in timer setting status

Press and hold the ON and OFF button simultaneously for 3 seconds, the LED will keep on.

Step 2:Set time delay

A: If there is no operation, the LED will turn off automatically and the transmitter will go to normal

working state; there is no time delay function.

B: While the LED is on, press the ON button ("I") 1 to 5 times to set the desired delay time, then

press the OFF button to confirm.

Press the ON button once, the LED will flash once, press the ON button again, the LED will flash

twice, if you press the ON button again, the LED will flash three times....etc. up to 5x, then the LED

stays on permanently and one round of adjustment time is over.

Pressing OFF ("0") confirms the desired time delay and ends the program.

C: LED status after start of timer setting program (press button "I"+"0" for 3 sec.)

Press ON ("I") x times, confirm the desired option with the OFF button ("0"):

1x => LED flashes once => press OFF button, 15s time delay set successfully

2x => LED flashes twice => press OFF button, 60s time delay set successfully

3x => LED flashes three times => press OFF button, 180s time delay set successfully

4x => LED flash four times => press OFF button, 30m time delay set successfully

5x => LED flash five times => press OFF button, 60m time delay set successfully

6x => LED only lights up => press the OFF button, only normal ON/OFF, no timer function

Note: The time delay only works while the ON button is pressed on the transmitter. With two channel

transmitters, the time delay for each channel must be set separately!

If you press the OFF button, the time delay will be stopped in advance!

Wireless wall transmitter with timer......: DWS-10T(1 Channel)+ DWS-20T (2 channels +2 timers)

Wireless wall transmitter without timer..: DWS-11(1 Channel)+ DWS-22 (2 channels)

Commissioning, function test

Put the receiver into operation properly (observe the operating instructions for the receiver). The

receiver is switched on or off by pressing the corresponding "I" or "O" button on the wireless wall

switch.

Technical specifications:

DWS-10T = 1 Kanal(RSW864T1)/ DWS-20T = 2 channels(RSW864T2)

Time Delay...........: 15s/60s/180s/30m/60m

Frequency ...................: 433.92MHz

Transmission power..............: <10 dBm

Transmission distance : max 50 m (open area)

Power supply .........: 3V battery, type "CR2032" (included)

Internal LED .................: lights up briefly when the buttons are pressed

Operating temperature .......: 0 to +35 °C

Maße (B x H x T) .........: ca. 80 x 80 x 14 mm

Reproductions of any kind require the written permission of the publisher.