dixell CoolMate XLR130C Инструкции по установке и эксплуатации - Страница 11
Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Контроллер dixell CoolMate XLR130C. dixell CoolMate XLR130C 20 страниц. Cool mate
Печатать страницу
DIGITAL INPUTS
odc Compressor and fan status when open door:
no = normal; Fan = Fan OFF; CPr = Compressor OFF; F_C = Compressor and fan OFF.
I1P Door switch input polarity: CL : the digital input is activated by closing the contact; OP : the digital input is activated by opening the contact.
I2P Configurable digital input polarity: CL : the digital input is activated by closing the contact;
OP : the digital input is activated by opening the contact
I2F Digital input operating mode: configure the digital input function: EAL = generic alarm; bAL = serious alarm mode; PAL = Pressure switch;
dFr = Start defrost; AUS = Relay AUX actuation; Es = Energy Saving; onF = remote On/OFF; HdF = Holiday function.
did Time interval/delay for digital input alarm:(0
I2F=PAL. If I2F=EAL or bAL (external alarms), "did" parameter defines the time delay between the detection and the successive signalling of
the alarm.
AUXILIARY RELAY CONFIGURATION
oA1 Auxiliary relay configuration (terminals 15-16): dEF = Not set it; ALr = alarm; FAn = fans; Lig =light; AUS = auxiliary; onF = on/off; dF2 =
second defrost (only for XLR170), cP2 = second compressor (only for XLR170).
AUXILIARY THERMOSTAT CONFIGURATION (terms. 15-16) – OA1 = AUS
ACH Kind of regulation for auxiliary relay: Ht = heating; CL = cooling
SAA Set Point for auxiliary relay: (-50,0÷110,0°C; -58÷230°F) it defines the room temperature setpoint to switch auxiliary relay.
ArP Probe selection for auxiliary: nP = no probe, the auxiliary relay is switched only by button; P1 = Probe 1 (Thermostat probe); P2 = Probe 2
(evaporator probe); P3 = Probe 3 (display probe).
AoP Alarm relay polarity (terms. 29-30-31): oP = 29-30 terminals open with alarm; cL = 29-30 terminals close with alarm
TO SET CURRENT TIME AND WEEKLY HOLIDAYS (
Hur
Current hour (0 ÷ 23 h)
Min
Current minute (0 ÷ 59min)
dAY
Current day (Sun ÷ SAt)
Hd1
First weekly holiday (Sun ÷ nu) Set the first day of the week which follows the holiday times.
Hd2
Second weekly holiday (Sun ÷ nu) Set the second day of the week which follows the holiday times.
Hd3
Third weekly holiday (Sun ÷ nu) Set the third day of the week which follows the holiday times.
N.B.
Hd1,Hd2,Hd3 can be set also as "nu" value (Not Used).
TO SET ENERGY SAVING TIMES (3SEC.
ILE
Energy Saving cycle start during workdays: (0 ÷ 23h 50 min.) During the Energy Saving cycle the set point is increased by the value in
HES so that the operation set point is SET + HES.
dLE
Energy Saving cycle length during workdays: (0 ÷ 24h 00 min.) Sets the duration of the Energy Saving cycle on workdays.
ISE
Energy Saving cycle start on holidays. (0 ÷ 23h 50 min.)
dSE
Energy Saving cycle length on holidays (0 ÷ 24h 00 min.)
HES Temperature increase during the Energy Saving cycle (-30÷30°C / -54÷54°F) sets the increasing value of the set point during the Energy
Saving cycle.
TO SET DEFROST TIMES (3SEC.
Ld1÷Ld8 Workday defrost start (0 ÷ 23h 50 min.) These parameters set the beginning of the eight programmable defrost cycles during workdays.
Ex. When Ld2 = 12.4 the second defrost starts at 12.40 during workdays.
Sd1÷Sd8 Holiday defrost start (0 ÷ 23h 50 min.) These parameters set the beginning of the eight programmable defrost cycles on holidays. Ex.
When Sd2 = 3.4 the second defrost starts at 3.40 on holidays.
N.B. :To disable a defrost cycle set it to "nu"(not used). Ex. If Ld6=nu ; the sixth defrost cycle is disabled
OTHER
Adr RS485 serial address (1÷247): Identifies the instrument address when connected to a ModBUS compatible monitoring system.
PbC Probe selection: (Ptc=PTC probe; ntc=NTC probe). It allows to select the kind of probe.
Rel Release software: (read only) Software version of the microprocessor.
Ptb Parameter table: (read only) it shows the original code of the dIXEL parameter map.
dP1 Probe 1 temperature (thermostat): it displays the temperature detected by the thermostat probe.
dP2 Probe 2 temperature (evaporator): it displays the temperature detected by the evaporator probe.
dP3 Probe 3 temperature (display): it displays the temperature detected by the display probe.
Pr2 Access to the protected parameter list (read only).
1592017000 XLR 130-170 GB r2.0 23.03.2015
255 min.) Time interval to calculate the number of the pressure switch activation when
÷
3SEC followed by
afterward
)
afterward
)
) – Only for models with RTC
XL130 - XLR170
11/20