Alto-Shaam 1000-MR2-1 Установка, эксплуатация и обслуживание - Страница 11
Просмотреть онлайн или скачать pdf Установка, эксплуатация и обслуживание для Холодильник Alto-Shaam 1000-MR2-1. Alto-Shaam 1000-MR2-1 19 страниц.
Печатать страницуs U b t I t l e
f o o d h a n d l I n g g U I d e l I n e s
pr odUct co ve r I ng
To maintain sanitation control when loading
the refrigerated cart, foods should be above
140°F (60°C) and should be tightly covered.
A tight cover is an important part of proper
chilling methods and must be used to prevent
the possibility of accidental contamination by
airborne bacteria.
Stainless steel pan covers may be used. Stainless
steel covered pans must include a label indicating
pan contents and use-by date. A cover of clear
plastic wrap is also acceptable.
When using plastic wrap as a food covering, make
certain the wrap comes in direct contact with the
surface of the product and extends around and
down each side of the pan. This is an important
step to ensure proper chilling times. Spacing left
between the plastic wrap and the surface of the
food creates an insulating air gap resulting in
more product heat retention and a slower chilling
rate.
Meat roasts and other larger, dense products
should be no larger than a weight of 8 to 10
pounds (4 to 5 kg) per item. Because of the density
of these products, chilling could take up to 4
hours. Due to longer chilling time required, it is
also suggested these items be chilled at the end of
the day with the chiller set in the automatic chill/
hold mode. This method provides the operator
with fully chilled product holding at a refrigerated
temperature on the following day.
Prior to chilling, roasts must be wrapped in clear
plastic and placed in the chiller. Do not slice
roasted meats until the day of service.
Portioned meat products such as pork chops or
meat patties should be chilled directly on the
sheet pans on which they were cooked. Cover the
sheet pans with clear plastic wrap for chilling.
After chilling, this type of product can be placed
in steam table pans for refrigerated storage.
o p e r a t I o n
MN-36246 (Rev. 1) 09/15 • MR2-1 Mobile Refrigerated Cart • 9
t I t l e
p o r t I o nI n g & p ac K ag I n g
1. During portioning and packaging operations,
all foods should be maintained at or above
140°F (60°C), or below 40°F (4°C).
2. If cooked foods exceed the processing capacity
of the refrigerated cart, place hot product in an
appropriate back-up hot holding device. Hold
hot foods at a temperature above 140°F (60°C).
If a hot food holding cabinet is not available,
place hot foods in short-term refrigerated
storage until these products can be loaded
into the refrigerated cart for the next available
processing cycle. Production of cooked foods
should not exceed the processing capabilities
of the chiller, therefore, do not adopt short-
term refrigeration as a routine practice but use
only in an emergency situation.
3. Fill containers to a 12 pound (5kg) limit or
maximum depth of 2" (51mm) of product.
Do not use plastic or Lexan
4. For faster cooling, place lids and over-wrap
materials directly on the surface of foods. As
previously indicated, air trapped between the
lid and food surface acts as an insulator and
will increase chill time.
5. For faster chilling times, place low profile
foods such as chicken quarters, fish fillets,
or ribs in low depth containers such as
1-1/2" (38mm) deep sheet pans.
6. Large cuts of meat and poultry that weigh
a maximum of 8 to 10 pounds (4 to 5 kg)
maximum should be individually wrapped
with tight fitting film and placed on sheet pans
in the chill cabinet.
containers.
®