Altrad BELLE TDX 650A Руководство по эксплуатации - Страница 12
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Строительное оборудование Altrad BELLE TDX 650A. Altrad BELLE TDX 650A 18 страниц.
Печатать страницу
GB
CAUTION
Before starting the engine, make sure that the Drive Lever is at Neutral, Vibration Lever is at OFF, and the Parking Lever is at ON
position.
1.
Open the fuel tap at the engine.
2.
Move the Throttle Lever on the Operation Handle to
the Full Throttle (Hare) position.
Start the Engine – Electric Start
3ai. YANMAR - Turn the Key Switch at the Throttle Lever to
Start
position, and hold it until the engine starts.
3aii. KUBOTA - From cool, hold on Heat
secs. Turn the Key Switch at the Throttle Lever to
Start
position, and hold it until the engine starts.
DO NOT crank for an extended period. Maximum 10 secs.
3b. After the engine has been started, make sure that the key is set to ON (I) position during
the operation. (Setting the Key Switch to OFF (0) position would not allow the generator to
charge the battery.)
Start the Engine – Manual Start
4a. Grasp the recoil starter handle.
4b. Pull the handle out slowly until you fee lstrong resistance.
4c. Slowly return the recoil starter to the initial position.
4d. Push the decompression lever down and then release it. The decompression lever will
automatically return to the original position when the engine starts.
4e. Grasp the recoil starter handle.
4f.
Pull the handle all the way out with a strong and even motion. Use two hands if necessary.
4g. Slowly return the starter handle to the initial position.
4h. If the engine does not start, repeat the procedure from step 4b.
5.
Move the Throttle Lever to LOW position, and let the engine run at idle
for a few minutes to warm up.
6.
After the engine has warmed up, the machine is ready for operation.
7.
Move the throttle lever to the high speed "H" position quickly to prevent
damage from occurring to the clutch. The "Full Throttle" position of this
machine has been preset at the factory to achieve optimum machine
performance.
DO NOT alter this setting since premature wear or tear can result, and
both engine and machine warranty will be automatically voided.
8.
Move the Parking Brake Lever to the right to disengage it.
NOTE: Negligence to disengage the Parking Brake before attempting to
drive the machine forward or reverse will result in the severe
damage to the parking brake mechanism as well as the drive system.
9.
Operators Control
9a. Throttle Lever
Always keep the Throttle Lever at High position during the operation.
DO NOT attempt to alter the travel speed by changing the engine
revolution.
9b. Drive Lever
Move the Drive Lever forward to drive the machine forward.
For reverse motion, move the lever backward.
9c. Vibration Lever
By shifting the Vibration Lever to ON position, the vibration mechanism
will be engaged, and produce the vibration.
10. Stopping the Engine
11. In preparation for stopping the engine, move the throttle lever
to LOW position.
12. Allow the engine to idle for 1-3 minutes.
13. Move the Throttle Lever to STOP position to stop the engine.
Then, set the Key Switch to "OFF" position. The buzzer will sound
when the Key Switch is set to ON while the engine is stopped.
14. Close the Fuel tap
15. Apply parking brake by swinging the Parking Brake Lever to the left.
Start / Stop Procedure
DO NOT let your hands off from the Starting Handle during the Starting procedures.
position for 10
YANMAR
THROTTLE
LEVER
VIBRATION
LEVER
12
KUBOTA
DISENGAGE
KEY
SWITCH
DRIVE
LEVER
ENGAGE