ClearSpan R024B00005 Руководство по установке - Страница 3
Просмотреть онлайн или скачать pdf Руководство по установке для Комплект для теплицы ClearSpan R024B00005. ClearSpan R024B00005 7 страниц. End panel
Печатать страницуASSEMBLY PROCEDURE
The steps below describe attaching a typical end panel
to a typical end frame of a ClearSpan™ building with a
roll-form frame. (See photo on previous page for rafter
outline.) Verify that all parts are included in the shipment.
Notify customer service for questions or concerns.
ATTENTION: The frame and end panels shown
throughout this guide may differ from your frame and end
panel. It is the responsibility of the owner/installer to adapt
these steps as needed to attach the actual end panel.
If the end frame is of a custom design, some components
contained in the installation kit may not be used. If
additional parts and fasteners are needed to connect the
panel to your end frame, contact your sales representative
to purchase these and for more information.
1.
Read these instructions and additional documentation
(if any) included with the shipment before you begin.
2.
Gather the tools, bracing, ladders (and lifts), and
assistance needed to reach the top of the end wall to
install the panel.
3.
Check the weather
before you install the end panel.
Do not install the end panel on a windy or stormy day.
4.
Attach the end panel to the end frame.
5.
Read the care and maintenance information at the
end of these instructions.
6.
Complete and return all warranty information as
instructed.
REQUIRED TOOLS
The following list identifies the main tools needed to
attach the end panel. Additional tools and supports may
be needed depending on the structure, location, and end
panel size and design.
•
Tape measure or measuring device
•
Variable speed drill and impact driver (cordless with
extra batteries works best)
•
Metal file and metal-cutting saw
•
Scissors or utility knife to cut strap
•
Hammers, gloves and eye protection
•
Ladders, work platforms, and other machinery for
lifting designed to work safely at the height of the
building and end wall.
ATTENTION: Consult the services of a qualified,
professional contractor if you are not familiar with the
installation of similar covers and end panels.
Revision date: 06.21.12
Important Information
UNPACK AND IDENTIFY PARTS
The following steps will ensure that you have all the
necessary parts before you begin.
1.
Unpack the contents of the shipment and place where
you can easily inventory the parts. Refer to the Bill of
Materials/Spec Sheets.
2.
Verify that all parts listed on the Bill of Materials/Spec
Sheets are present. If anything is missing or you have
questions, consult diagrams for clarification or contact
customer service.
NOTE: At this time, you do not need to open the
plastic bags containing smaller parts such as
fasteners and clamps (if present).
CUSTOM END PANELS
The procedures presented in this guide describe
attaching a typical end panel to a typical end frame of a
ClearSpan™ building. If you are attaching a custom panel
or a typical panel to an end frame that differs from what is
shown, some steps may not apply.
It is the responsibility of the owner/contractor to review the
steps in this guide and to adapt the procedures as needed
to account for differences.
If you have questions, consult the services of a qualified,
professional contractor familiar with the installation of
similar covers and panels.
END FRAME: FINAL CHECK
Before you attach the end panel, inspect the frame for
sharp edges or fasteners that could damage the panel.
1.
Verify that all end frame members are properly
secured.
2.
Verify that all bolts and clamps are tight.
3.
Recheck the end frame assembly for sharp edges
or clamps and bolts that may interfere with the
installation of the end panel. File or tape sharp edges
as needed.
4.
Reposition clamps and bolts as needed and tape all
rafter pipe joints with duct tape to protect the panel.
5.
Verify that the main building frame is properly and
adequately anchored.
DO NOT ATTACH AN END PANEL TO A FRAME
THAT IS NOT ANCHORED TO THE SITE.
6.
Remove the ratchets that secure the bonnet portion
of the main cover at each end of the original shelter.
(This step may not apply to all applications.)
7.
Continue by attaching the end panel.
3