Clearwater Enviro Technologies AG-200 Руководство по установке и эксплуатации - Страница 5
Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Контроллер Clearwater Enviro Technologies AG-200. Clearwater Enviro Technologies AG-200 8 страниц. Electronic lime scale control system for agriculture applications
Печатать страницуC.) Site Survey
(Continued)
Type of Pipe
- This ScaleBlaster AG commercial model will work on PVC, CPVC, PEX or copper pipe up to:
one and a half (1 ½) inch in diameter for the AG-150,
two (2) inches in diameter for the AG-200,
three (3) inches in diameter for the AG-300,
four (4) inches in diameter for the AG-400.
If the pipe is galvanized or magnetic pipe, the unit will not penetrate it and will not work. By magnetic pipe, we
mean that if you put a magnet on the pipe and it sticks, it is magnetic. The pipe may be stainless steel, or steel and
appear to be magnetic, but not magnetic. So please test with a magnet to make sure if there is any doubt.
THIS IS EXTREMELY IMPORTANT.
If you only have galvanized or steel pipe to install the unit on, there are two options. You can replace about a foot
or so of the pipe with either copper or pvc. If this is not possible, then a much larger ScaleBlaster model will be
required to work on this application. Consult your distributor or Clearwater Enviro Tech for more details.
Location of the install -
The exact location of the install depends on the application. Because ScaleBlaster has multiple
applications, it is impossible to list them all. However, the most desirable place to install the equipment is at the main water supply line
going to the building or in front of the equipment. If the system has recycled water, you can also place the equipment on that line. It is
best to consult your dealer or Clearwater Enviro Tech if you have any questions. Your main goal is to treat 100% of the water as often
as possible. The unit should stay on 24 hours a day. The unit can be installed to cycle with electrical timers and pumps. The unit must
be on when water is flowing.
The unit may be installed indoors or outdoors, as the unit is in a weatherproof, UL, CUL and CE listed enclosure. If outdoors, make sure
the install area is out of direct sunlight. In extremely hot or cold areas of the world, it may be best to enclose our power box / computer
in another box to protect the LCD window and other inside components.
The power unit should be mounted on a wall or solid surface within 5 ½ feet from an electrical outlet, and within ten (10) feet from the
pipe in which the signal cable will be wrapped. If the power unit has to be more than 10 feet of where the signal cable will be wrapped,
you should contact your dealer or call Clearwater Enviro Tech for assistance.
The ScaleBlasterAG commercial unit has a 115 VAC power plug on the end of the cord. If the electrical outlet is more than 5 ½ feet
away from where the power box / computer is mounted, you can add an UL listed and commercial grade extension cord of up to 25 feet.
This is not recommended, but can be done if necessary. If the outlet is 230 VAC, you can simply remove the power plug and wire it to
the power source. The unit will automatically adjust to 115 or 230 VAC with no adjustments required to the power box / computer.
Once the main water line (or line in front of the equipment) is located, identify a
SECTION OF STRAIGHT PIPE THAT IS AT
LEAST 18 INCHES
LONG, and at least one foot away from any major electrical interference (an electric motor, for example). This
straight section must be away from elbows, couplings, tees and valves. Any agitation in the water will make it difficult to properly hit
the water with the ScaleBlaster signal. If you locate a section of straight pipe, make sure it is away from the elbows, couplings, etc. as
much as possible – but if you have no other options and there are elbows or couplings close by, go ahead and install the equipment.
It is better to add an extension cord to the power cable than it is to try and increase the coil leads.
Page 5