Edic CR2 Руководство по эксплуатации - Страница 6
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Ультразвуковой очиститель ювелирных изделий Edic CR2. Edic CR2 9 страниц. Professional restroom cleaner
Также для Edic CR2: Руководство пользователя/оператора (19 страниц)
Печатать страницуHow to use an accessory heater:
1. Mount the Heater by lining up the two "legs" to the
two mounting brackets on the rear of the machine.
(19 on page 4)
2. Fill the solution tank of your CR2 with sufficient
water for the task at hand
3. Connect your heater's in hose (#2 on page 5) to #16
on page 4
4. Connect your 35 ft solution hose to #5 on page 5
5. Connect your 35 ft vacuum hose to number 7 on
page 4.
6. Connect your wand or upholstery tool to the end of
your 35ft solution hose
7. Connect the power cord on the machine and the
power cord to the heater to two separate plugs on
two separate circuits.
8. Turn the priming/pressure relief valve (15 on page
4) 45 degrees to the left to the open position
9. Turn the pump to the on position
10. Allow pump to prime
11. Close priming valve
12. Turn heater on and allow up to 3 minutes for the unit
to heat up.
You will know the heater is ready for use once the green
lamp shuts off the first time. Once you start cleaning car-
pet, the green lamp will turn on and off throughout your
job as the thermostats regulate the temperature.
Note: The heater is mainly to be used for carpet cleaning.
While the heater may provide some heat during chem-
ical application, it is unlikely to reach desired tempera-
tures during continous spray conditions.
Installing metering tips for the Chemical feed
system:
Remove the semi-clear hose from the bottle cap (8 on
page 4). Select the appropriate metering tip for the dilu-
tion required and push it into the tube on the bottle cap.
Metering tip color guide:
Tan
1.25oz/Gal
Turquoise 2.00oz/Gal
Pink
3.00oz/Gal
Brown
4.00oz/Gal
White
5.00oz/Gal
Chemical feed system and hard surface clean-
ing:
The chemical feed system is designed to deliver accu-
rate chemical dilution for touchless surface cleaning.
The chemical feed system is activated by low pressure
spraying and is not suited for chemical dispensing while
performing carpet cleaning. To clean hard surfaces:
1. Fill the solution tank of your CR2 with sufficient
water for the task at hand
2. Connect hoses and accessory pressure gun
3. Select the appropriate tip and install on the cap of
the chemical feed (number 8 on page 4)
4. Place a bottle into bottle holder (number 9 on page
4)
5. Take the feed tube attached to the cap (number 8 on
page 4) and place it inside the bottle.
6. Take the cap from number 8 on page 4 and thread it
onto the bottle of chemical to secure it in place
7. Turn the chemical dispensing valve (11 on page 4)
to the left to the word "SOAP"
8. Chemical will only draw in the "Low pressure"
setting of your pressure gun. To activate the Low
pressure setting, pop the collar of the gun out.
9. While in the low pressure setting, apply chemical to
the walls and fixtures starting from the lowest point
to the highest.
10. Spray the floor as you make your way out of the
room
11. Allow the chemical to dwell according to the chemi-
cal manufacturers recommendations
12. You may use the brush on your squeegee/brush
wand to agitate particularly soiled areas
13. When you are ready to rinse away chemical, simply
turn the Chemical dispensing valve to the right to
the word "RINSE"
14. Set your pressure gun to "high" pressure by pulling
the collar back in. Rinse surfaces starting from the
top down.
15. See "Recovering liquid" for final steps
6