djm direct DJMSL12 Руководство по эксплуатации - Страница 5
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Пила djm direct DJMSL12. djm direct DJMSL12 15 страниц. 12 double bevel compound sliding mitre saw
Печатать страницу
- Before further use of tool, it should be carefully checked to
determine that it will operate properly and perform its intended
function.
- Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions that may
affect its operation.
- A guard or other part that is damaged should be properly
repaired or replaced by an authorized service centre unless
otherwise indicated in this instruction manual.
- Have defective switches replaced by an authorized service centre.
- Do not use the tool if the switch does not turn it on and off.
21 - Warning
- The use of any accessory or attachment other than one
recommended in this instruction manual may present a risk of
personal injury.
22 - Have your tool repaired by a qualified person
- This electric tool complies with the relevant safety rules. Repairs
should only be carried out by qualified persons using original
spare parts, otherwise this may result in considerable danger to
the user.
WARNINGS. Before connecting a tool to a power source (mains
switch power point receptacle, outlet, etc.) be sure that the voltage
supply is the same as that specified on the nameplate of the tool. A
power source with a voltage greater than that specified for the tool
can result in serious injury to the user, as well as damage to the tool.
If in doubt, do not plug in the tool. Using a power source with a
voltage less than the nameplate rating is harmful to the motor. Your
tool is double insulated for additional protection against a possible
electrical insulation failure within the tool.
WEAR GOGGLES
WEAR EARMUFFS
WEAR A BREATHING MASK
WARNING! For your own safety read instruction manual before
operating mitre saw. Wear eye protection. Keep hands out of path of
saw blade. Do not operate saw without guards in place. Do not
perform any operation freehand. Never reach around saw blade.
Turn off tool and wait for saw blade to stop before moving workpiece
or changing settings. When changing the blade, replace and secure all
guarding to its original position and correctly before starting tool.
Disconnect power (or unplug tool as applicable) before changing
blade or servicing. Do not expose to rain or use in damp locations. To
reduce the risk of injury, return carriage to the full rear position after
each crosscut operation.
The tool must be used only for its prescribed purpose. Any use other
than those mentioned in this Manual will be considered a case of
misuse. The user and not the manufacturer shall be liable for any
damage or injury resulting from such cases of misuse.
The manufacturer shall not be liable for any changes made to the
tool nor for any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible to
eliminate all residual risk factors. The following hazards may arise in
connection with the tool's construction and design:
·Damage to the lungs if an effective dust mask is not worn.
·Damage to hearing if effective earmuffs are not worn.
·When operating the saw, use safety equipment including safety
goggles or shield, ear protection, dust mask and protective clothing
including safety gloves.
· Ensure that there is adequate general or localized lighting.
· Do not use the saw unless the guards are in place.
· Do not use the saw to cut metal or masonry.
· Do not let anyone under 18 years operate this saw.
· Ensure that the operator is adequately trained in the use,
adjustment and operation of the machine.
· Do not use this saw to cut firewood.
· Keep the area free of tripping hazards.
· Report faults in the machine, including guards and saw blades, as
soon as they are discovered.
· Ensure that the machine is always fixed to a work bench,
whenever possible.
· Always stand to one side when operating the saw.
· Never use a damaged or deformed saw blade.
· When cutting round wood, use clamps that prevent the
workpiece from turning on both sides of the blade.
· Never use your hands to remove sawdust, chips or waste close by
the blade.
· Use only blades as recommended by the manufacturer and which
conform to EN 847-1.
· Do not use blades of High Speed Steel (HSS blades).
· If the table insert is damaged or worn, have it replaced by an
authorised service centre.
· Rags, cloths, cord and string and the like should never be left
around the work area.
· Avoid cutting nails. Inspect the workpiece and remove all nails and
other foreign objects before beginning sawing.
· Support the work properly.
· Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw head
is not in the rest position or whilst the machine is running with an
unguarded saw blade.
· Do not attempt to free a jammed blade before first switching off
the machine.
4