Altronix HubSat42D Руководство по установке - Страница 2
Просмотреть онлайн или скачать pdf Руководство по установке для Переключатель Altronix HubSat42D. Altronix HubSat42D 8 страниц. Passive utp transceiver hub with integral camera power
Печатать страницуAltronix HubSat4D Passive UTP Transceiver Hub with Integral Camera Power transmits UTP video, RS422/RS485 data and
power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount enclosure. Video
transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when
utilizing Altronix HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit
features individually selectable 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the HubSat4D
can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cables
back to the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat4D
provides power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.
Agency Listings:
• UL Listed for Commercial CCTV Equipment (UL 2044).
CUL Listed - CSA Standard C22.2 No.1-04, Audio,
Video and Similar Equipment.
Input:
• 115VAC, 60Hz, 1.25A.
• Primary in-line fuse is rated @ 3.5A/250V.
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft. per channel.
• Four (4) 75 Ohm video outputs.
Data:
• RS422/RS485 data input.
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position.
HubSat42D
• HubSat4D with four (4) HubWayAv
Video Balun/Combiners for 24VAC Cameras.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
HubSat4D Passive UTP Transceiver Hub with Integral Camera Power.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure's
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the two fasteners. Place the enclosure's upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8).
Secure green wire lead to earth ground.
2. Set illuminated master power disconnect circuit breaker to the [OFF] position (Fig. 5a, pg. 6).
3. Connect 115VAC 60Hz to the black and white flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig. 5, pg. 6).
4. S elect 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat (Fig. 5, pg. 6) with the
corresponding output voltage switches. Select OFF position when servicing or installing individual cameras
(Fig. 1d, pg. 4).
5. Connect the BNC video outputs marked [Video 1-4] on HubSat to the corresponding video inputs on the
head end equipment (DVR) (Fig. 1a, pg. 4).
6. Connect terminals marked [+ DATA - - - ] on HubSat (polarity must be observed) to the RS422/RS485 output of the
head end equipment (DVR) (Fig. 1f, pg. 4). When using fixed cameras disregard this step.
7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]
on HubSat (Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
- 2 -
Overview:
Specifica tions:
Power (cont'd):
• Unit provides up to 1A max. per channel not to
exceed a total of 4A maximum current.
• PTC protected outputs are rated @ 1A per channel.
• Surge suppression.
Visual Indicators:
• Four (4) power LED indicators.
Enclosure Dimensions (H x W x D approx.):
8.5" x 7.5" x 3.5" (215.9mm x 190.5mm x 88.9mm).
Optional Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayAv2 - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
- HubWayDvi - for use with non-isolated 12VDC cameras.
Additional Models:
HubSat43D
• HubSat4D with four (4) HubWayDv
Video Balun/Combiners for 12VDC Cameras.
Installation Instructions:
HubSat4D