artisan TORO 3000 Руководство по эксплуатации и запасным частям - Страница 2
Просмотреть онлайн или скачать pdf Руководство по эксплуатации и запасным частям для Швейная машина artisan TORO 3000. artisan TORO 3000 16 страниц. Extra heavy duty cylinder bed lockstitch compound needle feed walking foot stitching machines
Печатать страницу
Table of Contents
I. Operating Instructions
A.
Caution Warnings
B.
Specifications
1.
CLEANING
2.
LUBRICATION. Where to oil the machine.
3.
HOW TO INSTALL THE NEEDLE
4.
HOW TO TAKE OUT THE BOBBIN
5.
HOW TO WIND A BOBBIN
6.
HOW TO INSTALL THE BOBBIN
7.
HOW TO THREAD THE MACHINE
8.
ADJUSTING THE STITCH LENGTH
9.
THREAD TENSION
10.
THE THREAD TAKE-UP SPRING
11.
ADJUSTING THE PRESSER FOOT PRESSURE
12.
FEED DOG ADJUSTMENT
13.
WALKING FOOT HEIGHT ADJUSTMENT
14.
SHUTTLE AND NEEDLE TIMING ADJUSTMENTS
15.
FEED TIMING ADJUSTMENTS
16.
TROUBLE SHOOTING GUIDE
II. Spare Parts List
1.
FRAME AND COVER COMPONENTS
2.
MAIN SHAFT COMPONENTS
3.
NEEDLE BAR & UPPER FEED COMPONENTS
4.
PRESSER BAR COMPONENTS
5.
FEED MECHANISM
6.
HOOK DRIVING SHAFT COMPONENTS
7.
TENSION COMPONENTS
8.
BOBBIN WINDER & THREAD GUIDE PARTS
9.
KNEE LIFTER COMPONENTS
We Strive to Continuously Improve our Machinery. Specifications and features are constantly being updated.
Your New TORO Stitcher may look slightly different then as shown in this pamphlet.
Page 3.
3.
4.
4.
5.
5.
5 and 31
6.
6 and 32
7.
7.
7.
8.
8.
9.
9, 10, 11, 12.
12.
13.
16.
17.
18, 19.
20, 21.
22, 23.
24, 25.
26, 27.
28, 29.
30.
2.
Winding the Bobbin on a TORO-4000 R
1. Raise the presser foot with the hand lifter lever.
2. Insert the bobbin onto the bobbin winder spindle.
3. Thread the winder in the order illustrated and wind the
thread four or five turns onto the bobbin.
4. Push the bobbin winder trip latch (A) down. When the
machine is operated the spindle will turn and start to wind
the bobbin.
5. When the bobbin is fully wound, the trip latch will
disengage and the spindle will stop.
To adjust the quantity of thread on the bobbin:
1.
Loosen the adjusting screw and nut number (B) and (C.)
and turn the screw counterclockwise to decrease the
amount of thread on the bobbin and clockwise to increase
the quantity of thread wound onto the bobbin.
2. Tighten the locking nut after adjusting for the correct
amount of thread to be wound onto each bobbin.
If the bobbin is not winding evenly, move the thread guide (D)
either left or right to compensate.
Several Bobbins can be wound while the machine is stitching.
TORO-3000 Bobbin Winder Instructions:
1. Place the bobbin on the spindle. Align the small pin with the hole
or slot in the bobbin.
2.
Insert the thread into the eye above the bobbin winder tension.
3.
Pull the thread around the and through the tension discs.
4.
Continue pulling the thread to the bobbin and wrap several turns of
thread around the bobbin.
5.
Push the Latch up against the center of the bobbin.
6. Operate the machine and the bobbin will begin to fill. Several bobbins can be
wound while the machine is in operation.
If the thread is wound too loosely, tighten the tension nut, if too tight, loosen the nut.
31.