CustomWorks INTIMIDATOR GSX2 Руководство - Страница 8

Просмотреть онлайн или скачать pdf Руководство для Игрушечный автомобиль с мотором CustomWorks INTIMIDATOR GSX2. CustomWorks INTIMIDATOR GSX2 17 страниц. Racing kit

Печатать страницу

Shock Bag

Bag J

-Parts for

Step#1

1426

Qty 2

Short Shock Body

-Parts for

Step#2

1432

Qty4

Eyelet Cap

-Parts for

Step#3

1433

Qty4

Spring Collar

STEP #1

1429 MED

1430 SHORT

NOTE: Put a few

drops of oil on the

O-Rings!

1425 MED

1426 SHORT

1434

TIP: To press clip in easiest, compress the

clip so the diameter is a little smaller.Insert

1250

open end of clip first, working counter-

1435

clockwise to the bent end as shown.

SHOCK FILLING INSTRUCTIONS:

1) Holding the

2) Slowly move the

shaft up and down

shock upright,

fill with oil until

several times to allow

the top of the

air bubbles to escape

body.

to the top.

SUGGESTED

40 WT R/C

SHOCK OIL.

6) Then the shaft

7) If the shock does not push

should push itself

out this far there is not enough

out to its full length

oil in it. Add just a little oil and

slowly.

try steps 5-6 again.

8) If the shockrebounds too fast , or you cannot

push the shaft in until the eyelet hits the body, there

is too much oil. Loosen the cap about 3 full turns,

then tighten again. A small amount of oil will seep

out again. Retighten the cap and try steps 5-6

again.

Shock Assembly

1425

Qty 4

1430

Med Shock Body

Short Shock Shaft

1431

Qty4

Threaded Cap

1446

Qty4

1488

Qty4

Front Spring

Rear Spring

BUILD 2 SHORT & 2 MED

5230

LENGTH SHOCKS!

- USE #1429 SHAFT WITH

1436

#1425 BODY.

- USE #1430 SHAFT WITH

#1426 BODY .

- Attach 1436 Shock Piston to

Shock Shaft using 5230 E-Clips

to secure.

- Press 1250 O-rings into the

Shock Body followed by 1434

Shaft Guide. Retain using 1435

Clip.

Filling Shocks: Steps 1-4

3) Refill with

oil to the top

of the shock

body.

Qty2

1429

Qty2

1434

Qty4

Med Shock Shaft

Shaft Guide

1:1

1437

Qty 4

FIRM Bladder (BLACK)

1407

Qty4

1408

Spring Bucket

Mount Ball

STEP #2

- Snap Pivot Ball into the 5228 Ball End. Thread

the Ball End onto the Shock Shaft until the Ball

End is flush with the end of threads on the shaft.

- Press 1432 Eyelet Cap into 1431 Threaded

Shock Cap so that guide in the Eyelet Cap lines

up in the recess in the Threaded Shock Cap.

- Press the 1437 Firm Bladder (BLACK) into the

Threaded Shock Cap so the dome of the

bladder points away from the Eyelet Cap.

- Fill the Shock Body with oil to the top then

thread the Eyelet Cap assembly onto the

Shock Body until tight.

-NOTE: See shock filling tips for more

instructions.

4) Thread the Eyelet Cap

assembly onto the Shock

Body until it is hand

tight. Oil should seep

out of the bleed hole

in the Threaded Cap.

2214

5277

1433

1407

- Thread 1433 Spring Collar onto the

shock. Slide 1488 Spring onto the

shock and secure using the 1407

spring bucket as shown.

- Press 5277 Screws thru the locations

shown. Fasten using 2214 Standoff.

1250

Qty 8

1435

Qty 6

O- Ring

Reatining Clip

5228

Qty4

Short Ball End

Qty4

5277

Qty 4

4-40 x 7/8 SH Screw

Setting Shock Rebound: Steps 5-8

5) Move the shock shaft in and out a

few times and then push it all the way

in. It should be easy to push the shaft

in until the eyelet hits the body.

STEP #3

5277 Screw

passes thru the

5217

inner most hole,

3rd hole from the

1408

bottom row.

1446 SPRING

5274

5277 Screw

passes thru the

inner/upper hole

on the Right

Front, the outer/

RIGHT

upper on the Left

FRONT

Front.

- Install the shocks onto the screws

with the shoulder of the 1408

Mount Ball facing away from the

tower, secure with 5217 Nut.

- Attach the shock to the susp

arms in the locations shown.

1:1

1436

Qty4

5230 Qty 10

Piston

E-Clip

5228

Qty4

Pivot Ball

5274

Qty 4

5217

Qty 4

4-40 x 1/2 SH Screw

4-40 Lock Nut

1431

1432

1437

5228

5277

LEFT

2214

REAR

5217

1408

1433

1488 SPRING

5274