DLS CLASSIC C5 Инструкции по установке - Страница 2

Просмотреть онлайн или скачать pdf Инструкции по установке для Динамики DLS CLASSIC C5. DLS CLASSIC C5 2 страницы. Classic series 2-way system

Печатать страницу

DLS C4, C5, C6 CLASSIC SERIES

Thank you for buying DLS CLASSIC 2-way system.

This instruction will help you to do a correct installation.

If you want to get the best sound from your speakers we advice

you to read and follow this instruction.

If possible mount the speakers in a baffle of MDF-board or similar

to avoid rattling.

For best result use high quality speaker cables, minimum 1,5 mm

For example the DLS SC 2 x 1,5.

MOUNTING:

Mount the speakers in the door or in the dashboard of your car.

Normally they will fit in the cars original mounting hole. If

possible reinforce with a baffle of MDF-board or similar. An in-

stallation high up on the door side is to be prefered. An

alternative installation is in so called kick panels down on each

side of the floor with the speakers facing up- and inwards

towards the listener. An installation of the tweeter close to the

bass/mid element is to be prefered. The tweeter can be installed

on the dash-board, or recessed in the door with the accessories

in the tweeter box.

It is important to fasten the speakers properly in order to avoid

bad sound and rattling.

The filters included with the speakers must also be fastened

properly to avoid rattling. Don´t place them close to the internal

wiring of the car, this can cause interference. Make sure the

cables don´t get jammed causing a short circuit to ground. This

can damage the amplifier circuits.

The speaker grilles are mounted in the plastic speaker frame by

the use of the rubber coumpound included in the packing.

Spread the compound even in the frame.

The sealing strip coming with the kit can be used for improved

sealing between the bass element and the mounting surface.

The tweeter installation is described in the instruction sheet

coming with the tweeters.

FACTS ABOUT DLS CLASSIC SERIES

Size

Nom. power (RMS)

Freq. range

Sensitivity

X-over frequency

Magnet diameter

Mount. depth bass

Mount. hole bass

Fs / Qts / Vas

Rec. box volume

If you have any questions about this product, contact

your local dealer, or DLS customer support center.

DLS C4

DLS C5

4" 10 cm

5,25" 13 cm

50 Watts

65 Hz - 20 kHz

60 Hz - 20 kHz

94 dB

93 dB

3500 Hz

70 mm

80 mm

58 mm

64 mm

102 mm

120 mm

89Hz / 0,67 / 1,8 l

62 Hz / 0,64 / 6 l

3-4 liter

5-6 liter

DLS Svenska AB

P .O. Box 13029

S-402 51 Göteborg, Sweden

Tel. +46 31 840060

Fax +46 31 844021

E-mail: [email protected]

www.dls.se

THE KIT CONTAINS:

2pcs bass/midrange elements with grilles and 6 dB filter

2 pcs of tweeters with 12 dB highpass cable filter

Mounting accessories and cables

Instruction

Speaker connection and tweeter

level select:

The filters coming with the system should be connected in

series with respective speaker element as on the drawing.

Select tweeter level by connecting the red cable to either the

red or yellow cable coming out from the high-pass filter. Make

your own tests for best result. Sometimes the midrange can

be improved by phase reversing the tweeter. Try it and make

your own judgement.

NOTE! The filters must be used. If the tweeters are

connected without filter they will be damaged and

the sound reproduction becomes bad.

CONNECTION:

2-way

system

connected

channel.

The

other

channel

should

connected in the same

way.

Car stereo / amplifier

DLS C6

6,5", 16 cm

60 Watts

50 Hz - 20 kHz

93 dB

3500 Hz

82 mm

62 mm

140 mm

67 Hz / 0,92 / 10 l

8-10 liter

SPEAKER PHASING

To be sure to have the correct speaker polarity (phase) you

can check this by using a 1,5 Volt battery.

Connect a cable from the battery plus-pole to the speaker

plus, and a cable from the battery minus to the speaker minus.

If the speakers are correctly connected the speaker cone

should move outwards on both right and left channel.

This check must be made on the cables going from the

speakers, to the output terminals of your car stereo or

amplifier.

Red +

Black -

one

Bass/mid

Red +

Black -

Tweeter

Filter

Speaker

high-

low-

impedance is 4Ω

pass

Tweeter level:

Red = high

Yellow = low

BUILDING BOXES

If you want to build a box to your

speaker a sealed type is to be

prefered. The box volume can vary

depending on how much bass you

want from your speakers. For

fullrange use of the speakers,

follow the recommended box

volumes in the table. If you want to

limit the reproduction at for ex. 100

Hz, divide these volumes by half.