Dobinsons BU59-3508 Краткое руководство по эксплуатации - Страница 4
Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Автомобильные аксессуары Dobinsons BU59-3508. Dobinsons BU59-3508 8 страниц. Bullbar for toyota landcruiser 100 series
Печатать страницу
Fitting Guide
1. Remove the number plate.
2. Remove the bumper bar or factory bullbar if
fitted.
3. Remove the factory tow hooks and keep aside
to refit later.
4. Install the bullbar mounting bracket and
winch mounting frame as per the diagram on
page 3. The Channel spacers (item 11) should
be installed with the flat side toward the top.
5. Install all bolts and tighten. The factory tow
hooks can be re-fitted under the winch
mounting frame, using the original bolts as
per the diagram on page 3.
6. Carefully un-wrap the bulbar taking care not
to scratch it especially on the top loops.
Reinstall the number plate. If installing driving
lights to the bullbar it is easiest to install now.
7. If not installing a winch skip to step 15.
8. See the Installation section of your Dobinsons
4x4 Winch manual for specific detailed fitting
instructions. For a brief overview see the
following steps.
9. Test fit your winch to the mounting bracket
and do up loosely with the clutch handle on
the left hand side of the vehicle.
10. This may require the clutch handle and gear-
box housing to be rotated forward one or 2
bolt holes to allow easy access through the
bulbar holes. See instructions in winch user
manual.
11. Determine where the winch control box will
be located and mount the control box. See
instructions in winch user manual for control
box mounting options. If mounting to the top
of the bullbar using the supplied bracket,
check clearance of control box to grill and also
check where the wires will route as if the
wires are passing through the holes in the top
of the bullbar the control box may not be able
to be wired until the bullbar has been fitted as
below.
12. Wire the winch up as per the winch
instruction manual and bolt the winch to the
mounting bracket, ensure the mounting bolts
Dobinsons Springs and Suspension
are not too long and tighten correctly. Route
the wires and connect to battery and also
route the breather hose.
13. Unwind some cable from the winch, and pass
the cable through the fairlead hole in the
bullbar and through the roller fairlead. This
may require removing a circlip from the
fairlead and re installing once the cable is
passed through.
14. Install the roller fairlead into the bulbar.
15. Check the poly bulbar over riders, fog light
and top loop bolts are tight (Do not over
tighten the stainless steel loop mounting
bolts. Do not over tighten the poly bullbar
over riders as they will pull the over riders out
of shape).
16. With help, fit the bulbar onto the mounting
bracket and loosely fit the mounting hardware
supplied.
17. Align the bar with the vehicle into its correct
position, leaving an even gap between the top
of the bullbar wing and the bottom of the
flare of about 10- 20mm.
18. Check for access to the clutch handle on the
winch.
19. Once you are happy with the alignment
tighten the nuts and bolts on each side.
20. Once happy with the alignment of the bullbar
drill 2 x 8mm pinning holes on each side of the
bullbar drilling through both the mounting
bracket mounting plate and bullbar mounting
plate. Fix with 8mm bolts and nyloc nuts to
keep the bullbar in its position.
21. Wire up the lights. Using a multimeter or test
light first locate the earth wire, parker positive
and indicator positive wires from the wiring
on the back of the original vehicle lights on
each side. This is easiest done by reaching in
behind the wheel arch liner and unclipping
both lights plugs for easier access.
22. Unclip the wiring from the indicator/parker
lights. Check that the wiring will be long
enough to reach the new bullbar
www.dobinsonsprings.com