Dodge SLEEVOIL RXT Руководство по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Промышленное оборудование Dodge SLEEVOIL RXT. Dodge SLEEVOIL RXT 12 страниц. Pillow blocks with self lubrication
Также для Dodge SLEEVOIL RXT: Руководство по эксплуатации (12 страниц)
Печатать страницу
3. NON-EXPANSION BEARINGS WITH DODGE SPLIT
THRUST COLLARS ('S' LINERS ONLY)
Split thrust collars are available for 'S' liners only. Remove clamp
screws from collars. Remove jam set screws and back out set
screws so they do not protrude into inside diameter of collar.
MATCH
MARKS
PART NO.
Place one half of collar on shaft with large chamfer next to shaft
shoulder. Rotate collar half around shaft and place other half in
position.
NOTE: Collar halves are match marked; do NOT assemble
halves with different marks.
Tighten clamp screws to torque specified in Table 2. Collar faces
MUST NOT be offset at split. Repeat for second collar.
Locate collars tight against shaft shoulders. This will allow 0.015 to
0.035 inch total running clearance between collars and liner thrust
faces. Tighten set screws to torque specified in Table 2. Install and
tighten jam screws on top of set screws.
Table 2 - Torque Values for DODGE Split Thrust Collars (in.-lbs.) ft.-lbs.
2-15/16
3-7/16
(96) 8
(96) 8
Screw
Set
(60) 5
(60) 5
Screw
Shaft Size
6
7
(inches)
(360) 30
(360) 30
Screw
LARGE CHAMFER
NEXT TO
SHAFT SHOULDER
3-15/16
4-7/16
4-15/16
(96) 8
(96) 8
(204) 17
(60) 5
(60) 5
(132) 11
8
9
10
(900) 75
(900) 75
(1800) 150
Set
(264) 22
Screw
4. INSTALLATION OF UPPER LINER
Apply oil to faces of thrust collars next to liner and to shaft in
journal area and to journal surface of upper liner.
Locate upper liner in place on lower liner, taking care to align dowel
pins and match marks. (The upper liner has a recess(es) for the oil
ring(s)). Make sure oil ring(s) rotate freely.
NOTE: 'T' liners have a rotation direction arrow mounted
to top of upper liner; arrow MUST point in same direction
as rotation of top of shaft. If not, liner must be removed,
reversed and reinstalled so arrow points in proper direction.
Install and tighten liner cap screws to torque listed in table 3.
Table 3 - Torque Values for Liner Cap Screws (in.-lbs.) ft.-lbs.
2-15/16
Liner
(58) 5
Cap
Screw
Shaft
6
(114) 10 (114) 10 (510) 43 (510) 43
Collars should run parallel to thrust faces of liner within .001 in.
Tighten housing base to pedestal. See Table 4 for torque.
5-7/16
(204) 17
(132) 11
12
(1800) 150
3
(264) 22
(264) 22
(264) 22
(1320) 110
3-7/16
3-15/16
4-7/16
4-15/16
(58) 5
(58) 5
(58) 5
(114) 10 (114) 10
7
8
9
10
(1050)
88
CHECK LINER THRUST FACE &
COLLAR CLEARANCE
(1320) 110
5-7/16
12
14
(1050)
(1050)
88
88
MATCH
MARKS