ClipperCreek HCS SERIES Руководство по установке - Страница 8
Просмотреть онлайн или скачать pdf Руководство по установке для Зарядное устройство ClipperCreek HCS SERIES. ClipperCreek HCS SERIES 9 страниц. Quad-mount kit.
innovative infrastructure for
electric and hybrid vehicles
Также для ClipperCreek HCS SERIES: Руководство по установке (20 страниц)
Печатать страницуSecure the bottom of the charger using one (1) 1/4-20 x
•
2" Torx button-head screws with neoprene washer and
HCS Plastic Angle Washer as shown in Figure 14.
For an installation with two chargers affixed to the
•
same post, repeat the previous steps for the opposite
side.
Figure 14: Mounting a Single HCS Charger:
Install bottom screw LAST
9. Connect the Wiring
The HCS has a flexible conduit extension with three
conductors. These conductors must be routed through the
side of the pedestal and the ninety-degree ½" NPT for
connection.
Trim the EVSE conduit to length. The recommended
•
length to remain is 12 inches as measured from the
bottom of the EVSE.
Route the three conductors that come through the
•
EVSE's flexible conduit through the NPT connection
and into the Pedestal Post.
No disassembly of the NPT Fitting is required. Push
•
the conduit onto the NPT Fitting ferrule and then
tighten the domed sealing nut on the NPT fitting.
For Dual-Mount Installations, repeat on the opposite
•
side.
All conductor and ground lug connections inside the
•
Pedestal Post must be completed at this time. The top
access hole will be blocked after this step.
10. Re-Install the Pedestal Post Cap
The pedestal cap is provided to cover the opening to
protect the conductors and inner pedestal from the
elements. Install the appropriate pedestal cap for a
single-mount or
dual-mount charger installation as
described below.
For Single-Mount Charger Installations:
Single-mount charger installations utilize the standard
•
post cap provided in the pedestal kit. This post cap
includes a flange on one side. Place the post cap onto
the top of the pedestal, with the flange facing the rear.
Align the screw holes on each side of the post cap
•
with the corresponding threaded inserts on the sides
of the pedestal.
Place a 1/4" Neoprene-bonded sealing washer around
•
HCS Series EVSE Pedestal Installation Guide
the shaft of two (2) 1/4-20 x 1" Torx button-head
screws. The metal portion of the washer should face
the head of the screw while the neoprene should face
the tip of the screw.
Secure the cap to the pedestal with the two (2) 1/4-20
•
x 1" Torx button-head screws (with washers) using a
T27 Torx driver.
For Dual-Mount Charger Installations:
Dual-Mount charger installations utilize a replacement
•
post cap provided in the Dual-Mount Kit. This post
cap lacks a flange at the rear. Place the post cap onto
the top of the pedestal.
Align the screw hole on each side of the post cap with
•
the corresponding thread insert on the side of the
pedestal.
Place a 1/4" Neoprene-bonded sealing washer around
•
the shaft of two (2) 1/4-20 x 1" Torx button-head
screws. The metal portion of the washer should face
the head of the screw while the neoprene should face
the tip of the screw.
Secure the cap to the pedestal with the two (2) 1/4-20
•
x 1" Torx button-head screws (with washers) using a
T27 Torx driver.
11. Install the Cover Plate
The cover plate is provided to cover the electrical access hole
for Single-Mount Pedestals only. Skip this step if you are
installing a Dual-Mount.
Secure the cover plate to the Single-Mount Pedestal
•
using two (2) 1/4-20 x 3/4" Torx flat-head tapered
screws using a T27 Torx driver until the screw head
is flush with the surface of the mounting plate.
Page 8 of 9
Figure 15: The Pedestal Post Cap