Cygolite CENTAURI-1000 Руководство по эксплуатации - Страница 2

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Аксессуары для велосипедов Cygolite CENTAURI-1000. Cygolite CENTAURI-1000 2 страницы. Ultra bright programmable smart light for cycling

Печатать страницу

HEADLIGHT OPERATION

WARNING: The headlight may get hot during use. Handle with caution. If the light is on and

stationary for more than 5 minutes, turn the light off.

The Centauri-1000 features a BICYCLING MODE with

4 brightness settings, and a SPECIAL MODE with a

fast flash, slow flash, walking, and S.O.S. settings.

These modes are controlled by the power button

BATTERY LEVEL

on the top of the headlight. Also, on top of the

INDICATOR

headlight are 4 indicators lights that show which

setting the headlight is in with the far left indicator

also functioning as a battery level indicator. The

headlight also features a full time OSP button which

gives you the freedom to program your brightness

level and flash tempo directly onto the light. The diagram

and instructions indicate where these features are located on the headlight and

how to properly use them.

BICYCLE MODE

SPECIAL MODE

1. From the off position, press and hold the

1. Plug the headlight cable to the battery

cable to turn light on in bicycle mode.

power button for 2 second to activate the

special modes.

2. Press power button to scroll through

the 4 brightness settings.

2. Press power button to scroll through the 4

special settings. Hold power button for 1

3. Hold the power button for 1 second to

turn the light off.

second to turn the light off.

LIGHT MODE INDICATORS

The 4 light mode indicators on top of the headlight show which setting is in use.

INDICATORS

BICYCLE MODE

4 on

High (100%)

3 on

Medium High(Programmable)

2 on

Medium Low (Programmable)

1 on

Low (Programmable)

BATTERY LEVEL INDICATOR

The battery level indicator is the LED on the far left of light status indicator. It flashes 3

different speeds to indicate the battery levels.

INDICATOR

BATTERY LEVEL

Constant with blink

Full to 1 hour left

Fast flash

Less than 1 hour left

Slow flash

Less than 20 minutes left

Headlight flashes

Battery empty

(light will shut off after 20 seconds)

OSP (ON-SITE PROGRAMMABLE)

OSP is the first smart technology by Cygolite that gives you the freedom to customize

your preferred brightness settings and flashing speeds directly to your headlight anytime,

anywhere. You can use the Centauri-1000 with the factory default settings or you can use

the OSP button to customize your preferred settings.

NOTE: HIGH will always be at 100% brightness and cannot be adjusted.

• View the indicator on the top of the light to confirm what brightness setting you are in, then begin

programming.

• HOLD the OSP button to gradually change the brightness and any time you RELEASE the button

the brightness will stop changing. HOLD the button again and the brightness will go in the

opposite direction. Repeat these steps to fine tune your brightness level. Once you've

reached your preferred brightness, RELEASE the button and that setting is saved.

• For the flash setting, follow the same steps to lengthen or shorten the time between the flashes.

• To restore factory default settings - While the light is in the ON position, press and HOLD the

power button for 7 seconds. The light will turn off, then turn back on with the factory default

settings.

WARNING: Use discretion when programming the Centauri while riding. Do not program your light

during times that require total attention. Cygolite cannot be held responsible for injuries that

may occur during use.

MOUNTING ON HANDLEBARS

1. Attach handlebar spacers to inside of handlebar bracket for standard sized and remove

them for oversized handlebars.

2. Swing thumbnut down from thumbnut slot to open bracket.

OSP BUTTON

LIGHT STATUS

3. Attach rubber pad to handlebar spacer. First remove paper from rubber pad to reveal

INDICATORS

adhesive side, align rubber pad holes to handlebar spacer plugs and join together.

4. Wrap bracket around handlebar and return thumbnut into slotted space.

5. Twist thumbnut clockwise until tight.

6. Slide headlight downward into bracket until headlight clicks into place.

Spacers

POWER BUTTON

TO REMOVE HEADLIGHT FROM THE HANDLEBARS

1. Press tab on bracket plate forward.

2. Slide headunit up.

TO ADJUST THE SIDE-TO-SIDE BEAM DIRECTION

Roll the headlight left to right to adjust the side-to-side direction.

MOUNTING ON HELMET

1. Add foam pad to underside of helmet bracket to cushion against the helmet. Peel back

white paper to reveal adhesive and fasten to the helmet bracket.

SPECIAL MODE

2. Weave the 12" long velcro strap up through one hole of the helmet bracket, then

Fast Flash (Programmable)

Slow Flash (Programmable)

through the plastic loop. Pull the strap until the plastic loop prevents the strap from

Walking

moving further.

S.O.S.

3. Position the helmet bracket above the helmet vent holes on the front top of the helmet.

4. Insert velcro strap downward through the vent hole then up through the opposing vent

hold. Thread the velcro strap through the helmet bracket and pull to tighten. Then

faster the velcro strap to itself, making sure the helmet bracket is sercured in place.

5. Sliding downward, insert the headlight bracket plate into the helmet bracket until the

parts lock in place. To remove the headlight, press the bracket tab forward and slide the

headlight up.

Foam Pad

6. Connect the headlight cable to the extension cable. Secure the extension cable to the

helmet by placing the 2" velcro on the top of the helmet. Remove the white paper on the

one side to reveal the adhesive material. Attach the adhesive side to the helmet and

separate the velcro strap from itself. Sandwich the cable in between the hook and loop of

the velcro strap to secure the cable in place.

7. Place the battery in your hydration pack or jersey pocket.

8. Adjust the helmet bracket up and down to your preferred viewing angle. If the swivel

becomes loose, tighten it with a phillips screwdriver.

Rubber Pad

MOUNTING THE BATTERY

1. An adhesive foam pad is included to provide cushion and grip between the battery and

the bike. Apply the foam padding to the center of the battery on the opposite side of

the velcro slot.

2. Thread the velcro strap through the velcro slot.

3. Wrap velcro strap around frame, through plastic loop, and fasten to itself.

CAUTION - When mounting the battery to the bike, make sure the battery cable and

battery velcro strap do not interfere with the brake cables.

Apply foam pad here

BATTERY CHARGING

1. Connect the charger to wall outlet first then the battery to the charger (Follow sequence for

proper charging.)

NOTE: The LED charging indicator on charger may take up to 30 seconds to turn on after

the battery and charger have been connected.

2. The LED on the Smart charger shows red when charging then green when fully

charged.

3. Allow approximately 7 continuous hours to fully charge a drained battery.

4. Disconnect charger and battery when charging is complete and not in use.

LED charging indicator

Red=Charging

Green=Fully charged

Battery

WARNING: Charge the battery with the supplied charger only. Using any other charger to

charge the battery will result in damage. The Smart charger is for indoor use only. Unplug

the battery and charger once the battery is fully charged.

RUN TIMES

NOTE: Run times are based on manufacture default settings. On the lowest possible setting using

OSP, the run time can be up to 60 hours. Therefore run time soley depends on your brightness

level that is programmed into the headlight using the OSP function.

Velcro Slot

Smart Charger

Allow approximately 7 hours

to fully charge

Centauri-1000

BICYCLE MODE

2.75 hrs

High brightness

Medium-High

4 hrs

Medium-Low

6 hrs

Low

12 hrs

SPECIAL MODE

Fast flash

28 hrs

Slow flash

13 hrs

Walking

60 hrs

SOS

60 hrs