Acquaer SUS050T Руководство пользователя - Страница 4
Просмотреть онлайн или скачать pdf Руководство пользователя для Водяной насос Acquaer SUS050T. Acquaer SUS050T 17 страниц.
Печатать страницу
WARNING
Do not pump flammable or explosive liquids such as oil, gasoline, kerosene, ethanol, etc. Do not
use in the presence of flammable or explosive vapors. Using this pump with or near flammable
liquids can cause explosion or fire, resulting in serious personal injury and/or property damage.
Always disconnect the pump from its power source before installing, inspecting, maintaining, or repairing.
Do not stand in water when the pump is connected.
Do not touch the pump housing while it is operating, as the pump may be HOT and can cause serious
skin burns.
Do not disassemble the motor housing. The motor has NO repairable internal parts, and disassembling
may cause oil leakage or dangerous electrical wiring issues.
CAUTION
This pump is designed for home sump applications. The pump is equipped with a 3-prong grounding-type
power cord. The ball bearings on the motor shafts never need to be lubricated.
This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for
a long time when properly installed, maintained, and used. However, inadequate electrical power to the
pump, dirt, or blockage by ice or debris may cause the pump to fail, eventually bringing about additional
water damage. To minimize the potential for water damage due to pump failure, please carefully read the
manual and follow the instructions regarding common pump problems and remedies or call
800-201-1360
This pump has not been tested or approved for use in swimming pools or in salt-water marine areas. It is
also not engineered to be run continuously as a "fountain" or "waterfall" pump. Because this pump
has an oil-filled motor, it should NOT be used in water containing fish. Pump only water with this pump.
For safety, the pump motor has an automatic resetting thermal protector that automatically will turn off the
pump if it becomes too hot. Overuse of this feature will damage the pump and will void the warranty.
Once the thermal protector detects that the pump has cooled to a safe temperature, it will allow the pump
to operate normally. If the pump is plugged in, it may restart unexpectedly.
Know the pump applications, limitations, and potential hazards.
1.
Make certain the electrical power source is adequate for the requirements of the pump.
2.
ALWAYS disconnect the power to the pump before servicing.
3.
Release all pressure (drain all water) within system before servicing any component.
4.
5.
Secure discharge line before starting pump. An unsecured discharge line will whip, possibly causing
personal injury and/or property damage.
Secure the pump on a solid base to keep the pump vertical and above mud and sand during operation to
6.
maximize pumping efficiency and prevent clogging and premature pump failure.
Check that all pipe connections are tight to minimize leaks.
7.
8.
Connect the pump DIRECTLY to a grounded, GFCI outlet.
Extension cords may not deliver sufficient voltage to the pump motor. Extension cords present a life
9.
threatening safety hazard if the insulation becomes damaged or the connection ends fall into water.
Make certain the electrical circuit to the pump is protected by a 15 Amp or larger fuse or circuit breaker.
10.
11.
Periodically inspect the pump and system components to be sure the pump inlets are free of mud, sand,
and debris. DISCONNECT THE PUMP FROM THE POWER SUPPLY BEFORE INSPECTING.
Wear safety glasses at all times when working with pumps.
12.
13.
Follow all electrical and safety codes, particularly the National Electrical Code (NEC) and in the
workplace, the Occupational Safety and Health Act (OSHA).
14.
This unit is designed only for use on 115 volts (single phase), 60 Hz, and is equipped with an approved
3-conductor cord and 3-prong grounded plug. DO NOT REMOVE THE GROUND PIN UNDER ANY
CIRCUMSTANCES. The 3-prong plug must be directly inserted into a properly installed and grounded
3-prong, grounding-type receptacle. Do not use this pump with a 2-prong wall outlet. Replace the
2-prong outlet with a properly grounded 3-prong receptacle (a GFCI outlet) installed in accordance with
the National Electrical Code and local codes and ordinances. All wiring should be performed by a
qualified electrician.
Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord.
15.
Do not use damaged or worn cords.