Ashdown Acoustic Radiator 2 Инструкция по эксплуатации - Страница 5
Просмотреть онлайн или скачать pdf Инструкция по эксплуатации для Усилитель Ashdown Acoustic Radiator 2. Ashdown Acoustic Radiator 2 5 страниц.
Rear Panel Facilities
ACOUSTIC RADIATOR 1 & 2
ACOUSTIC RADIATOR (RESO) 1
POST EQ D.I.
A Post-Eq balanced XLR D.I. output is provided for connection to the microphone
input of a mixing desk for either Direct Injection into the PA system or for recording.
EFFECTS SEND / RETURN
A serial loop is provided at a level of 0dB for connection to external effects units.
The effects send can also be used as a line out socket if required.
LINK / LINE OUT
This output can be used for connection to a Tuner as its output remains active when
the amplifier is Muted.This can also be used to 'Link' together 2 x Ashdown Acoustic
Radiators with a single jack to jack cable in a connection where both preamps drive
both output stages.
ACOUSTIC RADIATOR (RESO) 2
MUTE FOOTSWITCH SOCKETS
A standard latching foot switch can be used plugged into these sockets to mute the
Reverb or the Output.
LINE INPUT
This socket allows you to connect a line input from other units such as drum
machines, cassettes, CD, Minidisc etc. for amplification through the Acoustic Radiator.
This has its own level control to balance the external signal with your own playing
level.
EFFECTS SEND / RETURN
A serial loop is provided at a level of 0dB for connection to external effects units.The
effects send can also be used as a line out socket if required.
PRE / POST EQ D.I.
A balanced XLR D.I. output is provided for connection to the microphone input of a mixing desk for either
Direct Injection into the PA system or for recording.The switch next to this selects either a Pre-Eq or
Post-Eq & Post-Effects signal to be sent to this socket.
LINK / LINE OUT
This output can be used for connection to a Tuner as its output remains active when the amplifier is
Muted.This can also be used to 'Link' together 2 x Ashdown Acoustic Radiators with a single jack to jack
cable in a connection where both preamps drive both output stages.
MUTE F/S
LINE IN
EFFECTS
LINE OUT
D.I.
LEVEL
D.I.
POWER
OFF
ON
OUTPUT
REVERB
FX
FX
LINK/
PRE/
MUTE
MUTE
RETURN
SEND
TUNER
POST EQ
TO REDUCE THE
THIS APPARATUS MUST BE EARTHED.
RISK OF FIRE OR ELECTRICAL SHOCK
F O R
C O N T I N U E D
P R O T E C T I O N
DO NOT EXPOSE THIS EQUIPMENT TO
AGAINST RISK OF FIRE REPLACE ONLY
RAIN OR MOISTURE.
WITH SAME TYPE AND RATING OF FUSE.
UTILISER UN FUSIBLE DE RECHANGE DE
MEME TYPE ET CALIBRE.
MODEL No:-
ACOUSTIC
OUTPUT = 150 WATTS RMS
RADIATOR 2
300 WATTS PEAK
FUSE
SERIAL No:-
115V = T3.15A
240V = T2A
MANUFACTURED IN ENGLAND BY:-
.
ASHDOWN ENGINEERING
MAINS INPUT 200V A 115V @ 1.7A
Specificatio ns
ACOUSTIC RADIATOR 1 & 2
ACOUSTIC RADIATOR 1
MANUFACTURED IN ENGLAND BY:-
ASHDOWN ENGINEERING
INPUTS
THIS APPARATUS MUST BE EARTHED.
F O R
C O N T I N U E D
P R O T E C T I O N
AGAINST RISK OF FIRE REPLACE ONLY
Chan 1 Passive
WITH SAME TYPE AND RATING OF FUSE.
UTILISER UN FUSIBLE DE RECHANGE DE
MEME TYPE ET CALIBRE.
Chan 1 Active
TO REDUCE THE
RISK OF FIRE OR ELECTRICAL SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO
Chan 2 XLR & Jack
RAIN OR MOISTURE.
Effects Return
MODEL No:-
ACOUSTIC
OUTPUTS
RADIATOR 1
SERIAL No:-
Line Out
OUTPUT = 100 WATTS RMS
200 WATTS PEAK
Effects Send
POST EQ
D.I.
D.I.
POWER
OFF
GENERAL SPECIFICATION
FX RETURN
Bass & Treble
Frequency Response
ON
FX SEND
Signal to noise ratio
LINK/LINE OUT
Distortion
Notch
FUSE 115V = T3.15A 240V = T2A
.
MAINS INPUT 150V A 115V @ 1.3A
Output Power
ACOUSTIC RADIATOR 2
INPUTS
Chan 1 Piezo
Chan 1 Active
Chan 2 XLR & Jack
Effects Return
Line In
OUTPUTS
Line Out
Effects Send
D.I.
GENERAL SPECIFICATION
Eq
Frequency Response
Signal to noise ratio
Distortion
Notch
Output Power
Impedance 3.9M Ohms
Input range 150mV to 10V p-p
Impedance 10k Ohms
Input Range 300mV to 20V p-p
Impedance 600 Ohms balanced
Level -20dB to 0dBu
Impedance 47k Ohms
Level 0dBu
Impedance 4.7k Ohms
Level 0dBu
Impedance 10k Ohms
Level 0dBu
Impedance 600 Ohms
Level –20dBu
+/- 15dB @ 100Hz & 10kHz
-3dB @ 28Hz & 28kHz
<80dB (Eq flat)
>0.8% THD
Frequency 70 to 350Hz 'Q' = 5
100 Watts RMS
Impedance 3.9M Ohms
Input range 100mV to 15V p-p
Impedance 10k Ohms
Input Range 200mV to 30V p-p
Impedance 600 Ohms balanced
Level -20dB to 0dBu
Impedance 22k Ohms
Level 0dBu
Impedance 10k Ohms
Level 0dBu
Impedance 4.7k Ohms
Level 0dBu
Impedance 22k Ohms
Level 0dBu
Impedance 600 Ohms
Level –20dBu
+/- 15dB @ 100Hz, 340Hz, 660Hz, 1.6 kHz & 10kHz
-3dB @ 28Hz & 28kHz
<80dB (Eq flat)
>0.8% THD
Frequency 70 to 350Hz 'Q' = 5
150 Watts RMS