Acquisitions X-FIRES 600 Инструкции по установке и эксплуатации - Страница 9
Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Крытый камин Acquisitions X-FIRES 600. Acquisitions X-FIRES 600 14 страниц. Designer flueless fires
Печатать страницу8.4
FITTING THE DECORATIVE FRAME ASSEMBLY
All
models
Remove any pro-
tective packaging,
and remove any
protective
that may be pres-
ent on the frame.
The facia panel is
supported by four M6 screws which protrude
from the front of the outer casing.
Ensure each screw is unscrewed approxi-
mately one turn from the fully screwed in
position in order to create a 2mm gap (see
figure 9). Simply hang the facia panel onto
the outer casing
screws, ensuring that the corresponding key-
hole shaped holes engage the screwheads
fully (figure 10).
9.0
BRIEFING THE
CUSTOMER
All instructions must be handed to the user
for safekeeping. Show the customer how to
light and control the fire. After commissioning
the appliance, the customer should be
instructed on the safe use of the appliance
and the need for regular servicing. Frequency
of service depends on usage, but MUST be
carried out at least once annually. Advise that
cleaning of the fire maybe achieved when the
fire is cold using a damp cloth and mild deter-
gent on most surfaces. Advise that the fire will emit a "newness" smell for a time after initial commis-
sioning and that extra ventilation may be needed during this time. Recommend that a guard be used
for the protection of the young, pets, the elderly and the infirm.
10.0
SERVICING
Isolate the fire from the gas supply. Ensure that the fire is fully cold before attempting service.
A suggested procedure for servicing is detailed below.
1. Lay out the dustsheet and tools.
2. Remove the decorative frame/glass facia assembly. Removal is reverse of section 8.4.
3. Remove the glass door assembly (4 screws) and clean carefully.
4. Inspect the burner and the catalyst and clean if necessary with a soft brush.
5. Disconnect the gas supply.
6. Detach the burner front cover plate by removal of the four retaining screws. Undo the four
screws retaining the burner support brackets to the base and rear of the firebox. Remove the
control knob and spindle assembly from the valve by removal of the spindle retaining clip.
7. Remove the burner unit, strip off the burner pipes and clean thoroughly.
8. Clean the in-line restrictor, pilot assembly and the burner tube. Do not attempt to remove
the pilot injector as this can cause damage.
9. Re-assemble components.
10. Turn on the gas supply and leak test. Check pilot and burner for good ignition.
11. Refit the glass door assembly, ensuring correct orientation and a good seal.
12. Refit the decorative facia/frame assembly as detailed in section 8.4.
13. Check the purpose provided ventilation is un-obstructed.
14. Light the fire and test setting pressures.
15. Check safe operation of the appliance.
For specific servicing instructions, see relevant sections.
10.1
SERVICING THE BURNER UNIT AND GAS ASSEMBLY
Firstly, remove the decorative facia assembly as described in section 8.4. Remove the inner glass panel,
and disconnect the gas connection inside appliance. The gas connections to the gas valve can now be
released. Detach the burner front cover plate by removal of the four retaining screws. Undo the four
screws retaining the burner support brackets to the base and rear of the firebox, and remove the con-
trol knob and spindle assembly by removal of the spindle retaining clip. The burner may now be
removed.
:
2mm
film
Figure 9
starting with
the
lower
7
Figure 10
©
2012 Acquisitions of London