Ashly FET-I500M Технический паспорт - Страница 2
Просмотреть онлайн или скачать pdf Технический паспорт для Усилитель Ashly FET-I500M. Ashly FET-I500M 2 страницы. Ashly power amplifier specification sheet
Печатать страницуifications
Arch itect's Specif ication
Ashly Model l5O0M
The power amplifier. being oftwo channels, shall deliver a
minimum
power oI 175 watts per channel into 8 ohm
loads or 275 watts per channel into 4 ohm loads with both
channels operating. When switched into bridged mono
node. it shall deliver at least 550 watts into m 8 ohm
load. The amplifier
shall be immune
to damage from
shorted. open, or mismatched
loads. The amplifier shall
have a gain of 29dB t .5dB per channel and an input sen-
sitiviqr of 1.3 Volts ! 20/o lor lull rated output. Frequency
response shall be 10Hz Io 2OkHz t .5d8. It shall be stable
into any load including
pure capacitors and inductors.
Hum and noise shall be at least 110d8 below full output
and SMPTE intermodulation
distoftion
shall be less than
.010/o at full output. The amplifier shall have rear panel
switching for mono and bridging modes and rear mounted
level controls. The inputs shall be balanced bridging type
with male and female XLR type connectors as well as 1/4"
phone jacks. A three-color LED type indicator
shall be
employed to show the power level of each chamel and self
contained forced air cooling shall be used. The power out-
put devlces shall be of the Lateral MOS FET fpe.
The
anplifier
shall lveigh 371b. net and mount in a standard
19 inch rack using two spaces (3.5" high). The power
requirement shall be 1 10 125VAC. 50 60H2.
The porver amplitier shall be an Ashly FET- 1500M.
Ashly Model 1500C
'Ile
power amplilier, being of two channels, shall deliver a
minimum
power ol 175 watts per channel into 8 ohm
loads or 275 watis per channel into 4 ohn loads wiLh both
channcls
operating. When switched into bridged mono
mode. it shall deliver al leasi 550 watts into an 8 ohm
load. The amplifier
shnll be imntune
to dam:rge liom
shoried, open. or nisnratched loads. The amplifier shall
have a gain oi29dB t .SdB per ch:rnnel and an input sen-
sitivily of 1.3 Volts t 20/o lor ltll
rated output. F-requency
response shall be 1OLIz to 2OkHz, t .5dts. It shall be stable
inlo irny lo:rd inclllding pure capacitors and inductors.
IIum :rnd noise shall bc at lcast I 1Odts below llll output
ancl SMPI'E intermodulation clistortion shall be less than
.010/o at Iull output. Thc amplilier shall have rear panel
swikrhing lbr rrono and bridgine modes and rear ntounted
level controls. The inputs shall utilize 1/4' phonc.jacks as
well as terminal/barricr input strips. Sell conLait.red lbrced
air cooling shall be used.
'l'he
porver output dcvices shall
be ol the Lateral MOS-FET type. The nmplilier shall weigh
371b. net and mouni in a stanclard l9 inch rack usinq two
spaces (3.5' high), The power requirement shall be 110-
l2SVAC. 50-60H2.
The power amplilier shall be an Ashly FET- I 500C.
Ashly Audio Inc.
100 Fernwood Avenue
Rochester, New York 14621
ln Canada:
Gerraudio Dist
363 Adelaide Street East
^'