Blueprint Controllers BDAC-1 Инструкции - Страница 2

Просмотреть онлайн или скачать pdf Инструкции для Контроллер Blueprint Controllers BDAC-1. Blueprint Controllers BDAC-1 4 страницы. Digital atmosphere controller

Печатать страницу

Installation

• Mount the Controller on the wall. Place the remote sensor

at plant height in an area with good air circulation. Avoid

placing the sensor in a location with direct, intense exposure

to light.

• Connect the sensor cable to the bottom of the unit using the

quick- disconnect screw.

• Plug the Controller into a 120V NEMA 5-15 wall outlet.

• Flip the switch on the bottom of the unit to the ON position.

• Program desired settings before connecting any devices.

• Plug in and power on devices to be regulated by the Controller.

Caution

Ensure the devices being connected to the

Controller have the proper voltage and will

not exceed the maximum amperage rating

of the unit.

Warning

Do not expose the unit to water.

Factory Settings

The Controller is preprogrammed with the following

factory settings:

• Temperature Day Setting: 80°F

• Temperature Night Setting: 70°F

• Temperature Deadband: 3°F

• Day/Night Setting: 50% RH

• Humidity Mode: Decrease

• Humidity Deadband: 5% RH

• CO

Mode: Dayfree

• CO

On Time Duration: 1 minute

• CO

Off Time Duration: 30 minutes

• Temperature and Humidity Lock: Split

Restoring Factory Settings

Hold the "Enter/Reset" and DOWN arrow buttons for 3 seconds.

The display will read "f.Set." Press the "Enter/Reset" button again

to restore the default factory settings. When the process is

complete, the display will read "donE." Note: It may take up to 15

seconds to complete the process.

Error LEDs

When the Controller is functioning normally, the ambient

temperature and humidity will change slowly but steadily. If the

Controller does not detect a change in temperature or humidity

within a 1-hour period, the unit will deactivate the affected output

and the corresponding green error LED will flash to indicate

which device may be malfunctioning. Ensure the device and

remote sensor are functioning properly. To reset the error, press

the "Enter/Reset" button.

Adjusting Photocell Sensitivity

• Hold the DOWN arrow button for 3 seconds. The current

setting will be displayed.

• Press the UP arrow button to increase the number

displayed, decreasing the amount of light required to

activate the photocell.

• Press the DOWN arrow button to decrease the number

displayed, increasing the amount of light required to

activate the photocell.

• Press "Enter/Reset" to accept the new setting.

Selecting Temperature Settings

Temperature Display: Hold the UP and DOWN arrow

buttons for 3 seconds to change the temperature display

from Fahrenheit to Celsius.

Temperature Day: To set the temperature at which the

cooling output will be activated during the day, press the "Day

Setting" button. The display will read "dAy__F." Use the UP

and DOWN arrow buttons to adjust the setting. Press "Enter/

Reset" to accept the new setting.

Temperature Night: To set the temperature at which the

cooling output will be activated during the night, press the

"Night Setting" button. The display will read "nit__F." Use the

UP and DOWN arrow buttons to adjust the setting. Press

"Enter/Reset" to accept the new setting.

Temperature Deadband: To set the temperature deadband,

press the "Deadband" button under "Temp." The display will

read "d.b___F." Use the UP and DOWN arrow buttons to

adjust the setting. Press "Enter/Reset" to accept the

new setting.

Min/Max Temperature: Press the "Min/Max Temp" button to

display the minimum and maximum recorded temperature

values. Press the button again to cycle through the values.

Press "Enter/Reset" to reset a displayed value.

Selecting Humidity Settings

Humidity Day: To select the humidity level at which the

humidity output will be activated during the day, press the

"Day/Night Setting" button. The display will read "dAy_rH."

Use the UP and DOWN arrow buttons to adjust the

setting. Press "Enter/Reset" to accept the new setting.

Humidity Night: To select the humidity level at which the

humidity output will be activated at night, press the "Day/

Night Setting" button twice. The display will read "nit_rH." Use

the UP and DOWN arrow buttons to adjust the setting. Press

"Enter/Reset" to accept the new setting.