Asko 1325 Руководство по установке - Страница 9

Просмотреть онлайн или скачать pdf Руководство по установке для Посудомоечная машина Asko 1325. Asko 1325 12 страниц. User manual use & care guide general fr (french version)
Также для Asko 1325: Руководство по использованию (16 страниц), Руководство по эксплуатации и уходу (12 страниц), (Испанский) Uso Y Cuidado (12 страниц), (Французский) Manuel D'utilisation Et D'entretien (12 страниц)

Печатать страницу

REPLA

REPLACING

REPLA

CING

CING THE

CING

THE

THE T T T T T OE KICK BRA

THE

After you replace the guard plate (see page 7), you need

to replace the toe kick brackets. While holding the spring

tab on the base pan toward the outside of the machine,

slide the bracket into the

slots on the guard plate

and work it between

the guide slots on

the base pan.

INST

INSTALLING

INST

ALLING THE

ALLING

THE

INST

ALLING

THE

Once you have the toe kick bracket in place, you can

install the toe kick, as follows:

If you have not done so, remove the toe kick and felt

insulation from the brown paper packaging.

Lay the insulation on the back side of the toe kick to

make sure it fits properly.

Peel the adhesive protection strip off the insulation

and press it firmly to the back side of the toe kick,

making sure you don't cover any slots on the toe

kick.

Positioning the notches on the toe kick at the edge

of the access panel, slide the toe kick up behind

the access panel then let it slide to the floor.

Screw the toe kick to the toe kick brackets.

CHANGING

THE FR

CHANGING THE FR

CHANGING

THE FR

THE FRONT P

WARNING!

Before working on any electrical

appliance, be sure the electrical power has been

turned off at the breaker/fuse box.

Refer to the illustration at right for instruction references.

Remove the lower access panel with standard or

20 torx screwdriver.

Using needlenose pliers, remove the plastic plugs

around the edges of the access panel and upper

door panel. You may discard the plugs.

Using the screws provided with the trim kit, loosely

secure parts A and C to the upper door panel.

Slide the upper panel into the trim kit grooves.

Tighten the screws holding parts A and C.

Secure part B and tighten screws.

Loosely screw part E to the lower access panel.

Slide the custom panel into trim kit channels and

tighten the screw to part E.

Secure part D of the trim kit and tighten the screws.

10. Secure the lower access panel to the dishwasher.

11. Drop the access panel to line up with the lower

holes on the guard plate.

OE KICK BRACKETS

OE KICK BRA

Guard plate

THE T T T T T OE KICK

THE

OE KICK

ONT P

ANELS

ONT PANELS

ONT P

ANELS

CKETS

Adjusting the Bracket Depth

You will have to adjust the bracket depth to allow for the

thickness of the toe kick. To do this, first measure the

thickness of the toe kick. Then press the spring tab on

the sides of the base pan toward the outside of the

machine and carefully pull or push the bracket to the

required depth less the thickness of the toe kick.

NOTE:

Make sure the toe kick bracket is securely

inside the guides on the base pan.

Adjusting the Height on

Models 1805FI and 1895

These models come with two toe kicks. Use the

mounted toe kick if the machine will be 32-1/2" to

33-1/2" high. If it will be higher, use the toe kick

packed inside the dishwasher.

The toe kick has extended screw slots that allow you to

adjust the height. Position the toe kick so it touches the

floor and tighten the screws.

Extended screw slots

NOTE:

The stainless steel panels do not have holes

for custom trim. You have to drill the holes.

Panel Trim Kit

After you install the front panels, you should test the

door before you push the dishwasher into the cabinet

opening. If the door doesn't open properly, you may

need to adjust the door springs (see page 10).

Page 9