Amcor 000E AL-10 Kullanıcı El Kitabı - Sayfa 4

Klima Amcor 000E AL-10 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Amcor 000E AL-10 9 sayfaları. Amcor portable air conditioner owner's manual models al-10,000e al-10,000eh

Sayfayı Yazdır

Operation

Automatic Mode Indicator

High Fan Speed Indicator

Low Fan Speed Indicator

Room Temperature Indicator

Set Temperature Indicator

Temperature Up Selector

Temperature Down Selector

Fan Speed Selector Mode (Function)

Option Selector

Setting Mode/Function

Press the MODE button to select the required working mode: Automatic, Cooling, Fan or Heating (Heating is only

available for AL-10,000EH). The green indicator illustrating your selected mode lights up. It is recommended to select

Cooling or Heating mode and set your desired temperature, as the Auto mode has a preset temperature (please see

below) that cannot be changed.

The indicators of the functions in progress come on at the same time, e.g. Cool and Lo = Cooling mode with Low fan speed.

Auto Mode

When this mode is selected, the unit is preset to the following temperature settings and unit will only start to:

• Cool when room temperature is higher than 75ºF

• Heat when room temperature is lower than 68ºF (AL-10,000EH only)

If room temperature is between 68ºF and 75ºF, unit will stay in Fan mode. Again, when in Auto Mode, the temperature

settings cannot be changed.

Setting the Temperature in Cooling or Heating Mode

he display window's default is to display the ambient room temperature. The green indicator light under RT is on.

(RT = Room Temperature)

To set your desired temperature, press the Temperature up or down buttons (ranging from 62ºF to 90ºF). Each press

will increase or decrease your set temperature by 1ºF. When pressing the temperature up or down buttons, the

window will change to display your set temperature. At this time, the green indicator will light under ST (Set

Temperature). Once the temperature up or down buttons is released, the window will return to displaying the

ambient temperature after a second.

Note: When unit is in the following modes: Auto, Cool, or Heat - the compressor will cool/heat the room to reach

the set temperature. Once the ambient temperature has reached the set temperature, the compressor will stop and

unit will run in Fan mode. To conserve energy, the compressor will not start immediately after a couple degrees

increase or decrease, but will wait for a 5ºF allowance. For example:

In Cooling Mode with a set temperature of 70ºF

When compressor first stops after reaching 70ºF, unit will auto-switch to Fan.

Compressor will start cooling again when ambient temperature increases to 75ºF or above.

In Heating Mode with a set temperature of 72ºF

When compressor first stops after reaching 72ºF, unit will auto-switch to Fan.

Compressor will start heating again when ambient temperature drops to 67ºF or below.

In Auto Mode (with preset temperature of 68ºF for heat and 75ºF for cool)

Compressor will start cooling again when ambient temperature reaches above 80ºF or will start heating when

ambient temperature drops below 63ºF.

Cooling Mode Indicator

Fan Mode Indicator

Heating Mode Indicator

(For Models With Heating Options)

Timer Operation Indicator

Compressor Indicator

On/Off (Power) Selector

Timer Selector

Parts

Front

1. Control Panel

2. Cooling Air Outlet

3. Handle

4. Castors

Accessories

10. Adaptor - for insertion over the

hose and into the back of the

air conditioner

11. Exhaust Hose

12. Adjustable Slide Bar

13. Round Connector

14. Cap for Round Connector

15. Remote Control

(Electronic control models only)

Back

5. Air Filter

6. Air Inlet

7. Exhaust Air Outlet

8. Cord Hanger

9. Water Stopper (Rubber Plug Inside)

1 2