aero-naut Oldtimer XXL-59 İnşaat Talimatları - Sayfa 2

Hava Araçları aero-naut Oldtimer XXL-59 için çevrimiçi göz atın veya pdf İnşaat Talimatları indirin. aero-naut Oldtimer XXL-59 8 sayfaları.

Sayfayı Yazdır
Parts List
No.
Part
1.
Machine-cut sheets containing parts 1 - 13
2.
Balsa strip, 3 x 3 x 1000 mm
3.
Balsa strip, 3 x 3 x 500 mm
4.
Spruce strip, 2 x 5 x 500 mm, wing K19, K20
5.
Spruce strip, 2 x 3 x 500 mm, tailplane V07
6.
Balsa T.E. strip, sanded, left and right
7.
Balsa sheet, 1.2 x 80 x 630 mm
8.
Aluminium tube, 5 / 4 Ø x150 mm
9.
CFRP rod, 4 Ø x 112 mm
10.
Steel pin, 2 Ø x 35 mm
11.
Plastic horn
12.
Bag S1 – pushrod connectors
13.
Bag S1 – washer, 2.1 Ø
14.
Bag S1 – M2 locknut
15.
Bag S1 – socket-head grubscrew, M3 x 3
16.
Pre-formed piano wire pushrod, 0.8 Ø x 750 mm, one Z-bend
17.
Snake sleeve, 2 / 1 Ø x 1000 mm
18.
Metal hatch latch with spring-loaded pin
19.
Self-tapping screw, 2.2 Ø x 6.5 mm
20.
Plastic captive nut, M3
21.
Plastic screw, M3
22.
Plastic hinge, 15 mm
23.
Beech block, 12 x 12 x 15 mm, channelled
24.
GRP latch retainer
25.
Bag S2, jig consisting of four plywood parts
26.
Plywood spar web, 1 x 9 x 23, No. 26
27.
Plywood, 1 x 20 / 15 x 50 mm, tailplane mount, No. 27
28.
Spruce strip, 3 x 3 x 50, front tailplane stop-piece
Tools required
Sharp knife
•
Sanding block and abrasive paper (grits: 100, 180 and 240)
•
Fine-blade hacksaw (for metal)
•
Modelling pins and weights
•
Flat building board, at least 120 x 30 cm
•
Clear plastic film for covering the plan
•
Paper masking tape
•
Materials required to complete the model
(not included in the kit)
Wood-glue (PVA)
•
Thin / thick cyano-acrylate adhesive
•
5-minute epoxy
•
Covering tissue or film
•
Clear and coloured paint
•
RC system
•
Electric power system
•
The fuselage
Remove the fuselage formers T01 to T08 from the machine-cut sheets,
•
and write the part numbers on them using a soft pencil.
Repeat the procedure with the central fuselage plate T09. The whole
•
fuselage structure is based on this part.
The fuselage side frames are assembled from parts T12 and T12a.
•
Glue full-length 3 x 3 mm balsa strips to the inside of the fuselage side
•
frames T12 top and bottom; keep the strips exactly flush with the
outside edge of the side frames. If you are unsure, fit the fuselage
formers 'dry' (no glue) to check the fits.
Glue the formers T04 and T05 to the central fuselage plate T09: take
•
care not to mix up the front and rear ends of this part; the drawings
clearly show the correct orientation.
The central fuselage plate can now be glued to one side frame T12
•
together with the former T06.
Sand the outside of this assembly flat, so that it can rest flat on the building board. Lay the assembly on the building
•
board, and pin it down so that it cannot shift.
Building instructions - Oldtimer XXL-59
Oldtimer XXL-59
Quantity
15
4
4
6
1
2
1
1
1
1
2
2
2
2
2
2
2
1
4
1
1
2
1
1
1
8
1
1
2