Euro-Pro BIG SHARK EP134 Kullanıcı El Kitabı - Sayfa 3

Elektrikli Süpürge Euro-Pro BIG SHARK EP134 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Euro-Pro BIG SHARK EP134 4 sayfaları. 115v., 60hz., 7.8 amps
Ayrıca Euro-Pro BIG SHARK EP134 için: Kullanıcı El Kitabı (4 sayfalar)

Sayfayı Yazdır

Euro-Pro BIG SHARK EP134 Kullanıcı El Kitabı

OPERATING INSTRUCTIONS cont.

Cleaning & Changing the

HEPA Dust Cup Filter

Warning:

Always unplug the unit from

electrical outlet before opening the Dust

Cup (container).

Important:

Do NOT use the HEPA filter

cartridge without the debris screen in

place.

Warning

After each Use - Always

remove the Filter Debris Screen from the

HEPA Dust Cup Filter, then vigorously

"TapClean" HEPA Filter until no more

dust can be removed.

IMPORTANT, Please Note : The

"TapClean" HEPA Dust Cup Filter &

Debris Screen will stop most of the tiniest

dust particles and airborne allergens from

re-entering the air you breathe. In fact it

stops 99.97% of all particles as small as

0.3 microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Dust Cup

Filter will quickly accumulate, inside the

white filter folds, many fine dust particles

that are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly. This can

cause the motor to overheat and the re-

settable thermostat to trip. (Should this

happen turn off the switch, unplug the unit

and allow unit to cool down. Clean the

HEPA Filter and Debris Screen as

described in this section, then reconnect

unit and proceed with vacuuming.)

1. To open the Dust Cup (container),

push button and detach the Dust

Cup (container ). (Fig. 1)

2. Pull out the HEPA Dust Cup Filter

or cloth dust cup filter. (Fig. 2)

Fig. 1

Fig.2

3. Empty the dust from the Dust Cup

(container).

4. Separate the debris screen from the

HEPA filter cartridge by grasping the

debris screen with one hand and the

filter frame with the other and pull

apart. (fig. 3)

Debris

Screen

HEPA Filter

Fig. 3

5. Vigorously "TapClean"

Fig. 4

the HEPA Dust Cup

Filter on a hard

surface until no more

dust is observed

falling out from

between the pleats of

the filter. (fig. 4)

6. "TapClean" the Debris

Screen or rinse under

a faucet until clean.

(fig. 5) Remember that

the Debris Screen

must be completely

dry before reinstalling

in the vacuum.

7. Replace the Debris Screen on the

HEPA Dust Cup Filter and reinstall

filter assembly in the vacuum. (not

shown)

PLEASE NOTE: The white pleated

filter material in the HEPA Dust Cup

Filter will discolor over time -This is

NORMAL and will NOT affect the

performance of the filter. If the HEPA

Dust Cup Filter

is properly

"TapCleaned"

after each use

Fig. A

and suction

Wash only

does not return

once every

to 100%, then

three (3)

months.

we suggest that

Warning:

Allow 24

the HEPA filter

hours for drying before

be "TapCleaned"

replacing in unit.

vigorously until no

more dust can be removed, then

rinsed under the faucet and allowed to

dry for 24 hours before refitting into

the vacuum. (Fig. A) This should be

done not more frequently than

once every 3 months.

CAUTION

: The suction hole must be

open, free of any obstructions at all

times. Otherwise, the motor will overheat

and could become damaged.

CLEANING & CHANGING THE POST MOTOR FILTER

1. Disconnect from electrical outlet

before cleaning the filter.

2. Filter should be cleaned at least twice

a year or when it becomes visible

solid.

3. Always operate the cleaner with the

filter installed.

4. Do not use a washing machine to

rinse the filter.

5. Do not use a hair dryer to dry it.

Fig. 5

PROBLEM

Debris

HAND VACUUM

Screen

WILL NOT

OPERATE

HAND VACUUM

WILL NOT PICK-UP

OR SUCTION

POWER IS WEAK

DUST ESCAPING

FROM HAND

VACUUM

HAND VACUUM

HOSE OR

BRUSHES WILL

NOT PICK-UP

Push the Filter Cover Lock

to open the filter cover.

Remove the filter from the

grill-filter.

Rinse filter in lukewarm water

and dry the filter completely.

Put the filter into the grill-filter.

A severely solid or clogged filter

should be thoroughly washed

with fresh tepid water. A mild

detergent can be used if required.

TROUBLE SHOOTING GUIDE

POSSIBLE REASON

POSSIBLE SOLUTION

Power cord not firmly plugged

into outlet.

No power in wall outlet.

Needs servicing.

Thermostat has tripped.

Dust cup s full.

Unit clogged.

HEPA Dust Cup Filter needs

cleaning or replacing.

Dust cup is full.

HEPA Dust Cup Filter is not

installed correctly.

There is a puncture/hole in

HEPA Dust Cup Filter.

Hose clogged.

Dust cup is full.

Plug unit in firmly.

Check fuse or breaker.

Replace fuse/reset breaker.

Call 1-800-798-7398.

Turn the unit off and unplug

from outlet.

Allow unit to cool down,

then Restart. Empty dust

cup – (see page 4).

Turn unit off and unplug

from wall outlet. Remove

HEPA Dust Cup Filter and

check for object(s) in air

duct and remove.

Clean or replace HEPA

Dust Cup Filter.

(see page 4)

Empty dust cup.

Review HEPA Dust Cup

Filter instructions.

(see page 4)

Replace HEPA dust cup

filter. (see page 4)

Remove hose and/or

bushes. Remove obstruction

from hose.

Empty and clean dust cup.