AkuSense KIM07-0204NP Kullanıcı Kılavuzu

Ölçüm Cihazları AkuSense KIM07-0204NP için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. AkuSense KIM07-0204NP 2 sayfaları. Label detection

Sayfayı Yazdır

AkuSense

Label detection

KIM07Series

User's Manual

• Thank you for choosing AkuSense products. Please read this instruction carefully

before using the product.

• For your convenience, please keep this instruction carefully so that you can check it

at any time.

SYMBOL

The following symbols are important information in this manual, please be sure to

observe the following.

It is indicated that if you ignore the tag and erroneous operation,

it may cause death or serious injury.

In addition, significant material losses may also be suffered.

There is the risk of causing malfunction or fire, please do not

exceed the rated voltage when using.

There is a risk of rupture, do not use AC power.

Danger of burns at high temperatures.

SAF ETY PRECAUTIONS

To ensure your safety, be sure to observe the following.

• Do not use in flammable, explosive gas environment.

• Do not use in water, oil, chemical droplets environment, and exposure to steam

environment.

• Please do not disassemble, repair, rebuild this product.

• Do not use beyond the rated voltage and current range.

• Do not use beyond the rated environment.

• Please pay attention to the polarity of the working power, do not take the wrong line.

• Please connect the load correctly.

• Do not short-circuit the load.

• Please do not use the case damaged. When discarded, dispose of as industrial waste.

• Do not use in direct sunlight.

• Depending on the operating conditions (ambient temperature, supply voltage, others),

the temperature of the sensor surface may increase. In operation and cleaning, please

note that there is a danger of burns.

NOTIC E FO R US E

• Do not use in the following places :

Daylight direct place

High humidity, easy to open places

Place containing corrosive gases

Vibration, shock directly to the product body of the place

• This product wire and power lines used in the same piping, will be disturbed, malfunction

or even destroyed.

• The extension wire must use a wire with a cross-sectional area of 0.3 mm2 or more and a

length of 100 m or less. When the Korean S-mark certification model is used as a

certification product, please set it below 1 Om.

• For the force applied to the wire, please refer to: below 40N, 0.1 N.m torque less, 20N or

less, and 3Kg below the bending.

• When the power is turned on, the product can be detected within 200ms. So if the load

and product connected to a different power supply, you must first turn on the product

power.

• When the power is turned off, the output pulse may be generated, so please cut off the

power supply of the load or load line.

• Please do not use thinner, gasoline, acetone, kerosene and other solvents to clean up.

PACKAGE CONTENTS

• Sensor

1 piece

• User's manual

1 piece

OPERATION METHOD

Detection setting

Place the label bottom paper in the detection slot marked with an arrow, press the'+ -

button simultaneously with both hands until the indicator light flashes, then release at the

same time; move the sensor on the label so that the arrow is on the label to be tested. Press

the'-' button until the flashing light is off.

Output setting

In the state where there is no detection object in the sensor slot, press the'+ - button at the

same time, and then release it at the same time for 6 seconds to switch between LON and

D.ON;

Key lock

In the state where there is no detection in the sensor slot, press the'+ - button at the same

time, and then release it for 3 seconds, then you can switch the button lock and unlock.

TECHNICAL SPECIFICATIONS

No.Model

KIM07-0204NP

Detection distance

3mm

Slot depth

42mm

Slot width

3mm

Llight source

Infrared light (940nm)

Switch mode

Selectable Lon, D.on

Operating voltage

12-24V DC±10%

No-load current

40mA

Load current

100mA

Response frequency

10KHz

Response time

�20us

Reverse polarity protection, Output short circuit protection,

Protective circuit

Interference suppression

Protection degree

IP65

Material

Aluminum

Wiring

MB 4-pin plug

Weight

35g

Output method

NPN/PNP

Ambient brightness

Sunlight:S.1 0000Lux

DIMENSIONS

;:i 1 1

JI I

c:::

�

68.5

57.25

.- I�:

�

_______.

�

CIRCUIT DIAGRAM

NPN/PNP

12-24V DC

NPN

PNP