American Standard Salem 14 0155.017 Teknik Özellikler
Küvetler American Standard Salem 14 0155.017 için çevrimiçi göz atın veya pdf Teknik Özellikler indirin. American Standard Salem 14 0155.017 1 sayfaları. Recess bath enameled steel
Sayfayı Yazdır
BARRIER FREE
SALEM 14™ RECESS BATH
❏
0155.017 Right hand outlet
❏
0153.015 Left hand outlet
Product Features:
• Acid resisting, heavy gauge, enameled
steel one-piece recess bath
• Integral apron
• End drain outlet
• Slip-resistant surface
• Straight tiling bead
• Fully-bonded support pad
Nominal Dimensions:
1524 x 762 x 356mm
(60" x 30" x 14")
Bathing Well Dimensions:
1346 x 610 x 337mm
(53" x 24" x 13-1/4")
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4 for Enameled Steel Plumbing
Fixtures
• ASTM F-462 for Slip-resistant Bathing Facilities
To Be Specified:
❏ Color:
❏ Bath Faucet*:
❏ Faucet Finish:
❏ Drain: 1583.470
* See faucet section for additional models available
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
INSTALL WITH SEAT AT HEAD END.
© 2008 AS America Inc.
OPTIONAL TO FINISHED TO FINISHED
NOTE: NO CONCEALED
FLOOR (USUALLY BETWEEN 1651 to
PIPING FURNISHED
1981mm ( 65" & 78')
SHOWER 1/2" S.P.S.
711mm
(28)
FINISHED
WALL
C/L OF SHOWER CURTAIN ROD
(USUALLY 1930mm (76")
FROM FIN. FLOOR)
C/L OF VALVES
102mm
(44mm [1-3/4"]
(8)
DIA. HOLES)
102
(4)
SPOUT
305mm
1/2" S.P.S.
(12)
102 (4)
ROUGH
FLOOR
1-1/2 N.P.T.M. THREADS
13mm
(1/2)
1-1/2 O.D. TAILPIECE
SUMP PAD
NOTES:
0153.015 LEFT HAND OUTLET (SHOWN).
0155.017 RIGHT HAND OUTLET (REVERSE DIMENSIONS).
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH BATH FOR
ADDITIONAL INFORMATION.
SHOWN WITH POP-UP C.D. & O.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
CONCEALED PIPING NOT INCLUDED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4. These measurements
are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
H162
SALEM 14™
RECESS BATH
ENAMELED STEEL
1/2 S.P.S. OR 1/2"
C.W.T. SUPPLIES
203mm
229 x 305mm
(8)
(9 x 12") CUTOUT
19mm
(3/4)
197mm
(7-3/4)
C/L OF DRAIN
FINISHED
1524mm
WALL
(60)
365mm
(14-3/8)
FINISHED
WALL
356mm
(14)
19mm
(3/4)
762mm
(30)
PLUMBER NOTE:
PROVIDE SUITABLE FULL LENGTH
SUPPORT AT THIS POINT.
Revised 2/08
76mm
(3)