eKey CP DRM Hızlı Başlangıç Kılavuzu - Sayfa 2

Güvenlik Sistemi eKey CP DRM için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. eKey CP DRM 2 sayfaları. Access system with fingerprint scanning

Sayfayı Yazdır

INITIALIZING THE DEVICES-

The devices have to be initialized both for a new installation and when one of the devices has been replaced.

Only after this has been done can fingerprints be saved. Please follow the steps below:

DISPLA Y

KEY

DISPLA Y

KEY

STROKE

START

Select language

If you have only replaced the ekey home CP DRM, and you are using an ekey home

finger scanner on which fingers have already been saved (e.g. replacement due to a

defective CP), you can keep all the saved fingers by swiping a saved finger over the

sensor. If you strike the ESC key, then all the fingers will be deleted!

RECORDING FINGERPRINTS-

When you record a user´s fingerprints, you:

Set the user name

Select the finger to be used (you can save up to 10 fingers / user; but you cannot save more than

99 fingers in the whole system)

Record the finger's reference template

DISPLA Y

Enter security

DISPLA Y

code

START

See

The numbers mean that these fingers have already

been enrolled for the corresponding relay:

1 ... Relay 1

2 ... Relay 2 (only for ekey home CP DRM 2)

3 ... double relay (only for ekey home CP DRM 2)

DEFINING THE RELAY SWITCHING TIMES-

The switching time of each relay can be set from 1 sec to 99 sec. If you select 0 sec, then the relay operates in

bistable mode (= the relay changes its switch status, which then remains as such, until the next switching). The default factory setting is 3 sec.

DISPLA Y

Enter sec urity

DISPLA Y

code

START

See

Select the menu item

„Set relay time"

CHANGING THE SECURITY CODE-

Change the security code. Factory setting is „99".

DISPLA Y

Enter sec urity

DISPLA Y

START

code

See

Select the menu item

„Security code"

PLEASE CHECK THE USER´S GUIDE ON OUR HOMEPAGE

DISPLA Y

KEY

DISPLA Y

KEY

DISPLA Y FOR 2

STROKE

SEC

The devices have now

been initialized. You

may start enrolling

KEY

DISPLA Y

KEY

DISPLA Y

STROKE

Select user num ber

STROKE

Set user name

Select user

Strike

to scroll up

number

to the user name and

set the user name

(digit 1 to 9)

KEY

DISPLA Y

KEY

DISPLA Y

STROKE

Set relay 1 time

Set relay 2 time

(only for

ekey home CP DRM 2)

KEY

DISPLA Y

KEY

DISPLA Y

STROKE

Enter the first digit of

Enter the second

the new code

digit of the new code

www.ekey.net

FOR ADDITIONAL MENU ITEMS.

ENTERING THE SECURITY CODE –

code is „99". Change this code as soon as you have started up the system, in order to be protected against manipulations.

CODE

explains how to change the code:

DISPLA Y

KEY

STROKE

START

users->

see

Repeat until complete user

only for ekey home CP DRM

name is set

(9 digits)

KEY

DISPLA Y

KEY

DISPLA Y

KEY

STROKE

Select finger

STROKE

Select re lay

STROKE

Select finger

Select relay

DELETING USERS-

DISPLA Y

KEY

DISPLA Y

START

STROKE

ZnR = Status after Reset or Power

failure. Only if the relay switching time

has been set to 00.0 (b istable mode)

-...the relay remains off after reset or

power failure.

I ... the relay resumes the status it had

before the reset or power failure.

RESETTING TO FACTORY SETTINGS -

KEY

DISPLA Y

STROKE

START

The security code allows you to avoid system manipulations by unauthorized people. The factory default setting for this

DISPLA Y

KEY

DISPLA Y

KEY

STROKE

SECURITY CODE D igit 1

SECURITY CODE D igit 2

DISPLA Y

SWIPE THE

FINGER OVER

THE SENSOR

At least 3

times

It has not yet been possible to capture 3 fingers, or the

captured finger is of poor quality.

Although a finger has been swiped over the finger

scanner, the device has not discerned any finger swipe.

Read chapter 5

The finger image is of very poor quality. Try it once

again, read Chapter 5

The quality of the finger image is good, but not excellent.

You may either exit enrollment by pressing

the OK button

or try once more.

It is only possible to delete users. It is not possible to delete individual fingers of one same user!

Enter sec urity

DISPLA Y

KEY

DISPLA Y

code

STROKE

See

Select the menu

Select the user to

item „Delete user"

be deleted

WARNING! All the fingers which have been enrolled will be deleted!

DISPLA Y

Enter sec urity

DISPLA Y

KEY

code

STROKE

See

Select the menu item

„Reset"

CHANGING THE SECURITY

DISPLA Y

DONE

You now are in the main

menu and may change

system settings as you wish!

Should you have entered 3 times in a row

a wrong security code, then your system

will be locked for half an hour!

DISPLA Y

3 x green ...Finger

accepted

The finger has been

enrolled and in this

example it has been

assigned to relay 2!

Now you can enroll

additional fingers or

jump back to the main

menu by striking the

key.

KEY

DISPLA Y

KEY

DISPLA Y

STROKE

This

user´s

fingers

will

all

deleted! The user name is set back

to the factory settings.

DISPLA Y

KEY

DISPLA Y

DONE

STROKE

Your ekey home system

has now been reset to

the factory settings. All

the fingers have been

deleted! For a new

start-up go back to

„A:

INITIALIZING

THE DEVICES"